Lexus Recalls
Every Lexus safety recall in DVSA's recalls data, with the models each one covers.
Last updated 22 November 2026
Short answer:
DVSA's recalls data lists 41 safety recalls for Lexus vehicles since 1995, the most recent dated 1 December 2025. A recall only applies to vehicles built within set dates or VIN ranges, so check a registration with our free reg lookup to see whether that car has an outstanding recall, then confirm on GOV.UK.
Check a registration for outstanding recalls, free
Lexus recalls by model
| Model | Recalls listed | Latest recall |
|---|---|---|
| Lexus NX | 1 | Dec 2025 |
A recall can cover more than one model, so model counts can add up to more than the make total.
Latest Lexus recalls
The 30 most recent. Open a model above for its full list.
| Date | Recall | Vehicles affected |
|---|---|---|
| Dec 2025 | Parking assist ECU reprogram on multiple modelsFault: For certain vehicles equipped with a Parking Assist ECU a component of the Panoramic View Monitor (PVM) system that displays the rear view image the software may cause the rear view image to freeze or not display Fix: Reprogram the parking assist ECU. | 20,855 |
| Nov 2025 | Combination meter reprogramming on multiple models (LEXUS)Fault: For certain vehicles equipped with the combination meter system (where various information is displayed) that due to an improper programming of the combination meter unnecessarily repetitive data is written to a memory device. This may cause the memory device to deteriorate and the monitor to not display during the meter at start up and remain in this state permanently. Fix: Reprogram or replace the combination meter. | 24,549 |
| Nov 2025 | Electric compressorFault: For affected vehicles due to the programming of the HVAC control ECU software under certain conditions such as a specific failure mode of the electrical compressor the HVAC system will enter a failsafe mode that suspends the heater operation of the system and affects defroster function. Fix: Reprogram the HVAC control ECU and inspect the compressor . | 4,089 |
| Oct 2025 | Electric heater replacementFault: For affected vehicles there is a possibility that the electric heater could fail when exposed to stress over time causing heater operation to become inoperative. Fix: Replacement of the heater sub assembly. | 1,768 |
| Aug 2024 | Lss & tss 3.0 forward recognition camera on multiple modelsFault: Due to the programming of the forward recognition camera software there is a possibility that the memory inside the forward recognition camera could fail during processing when the ignition is turned OFF. If this occurs the PCS will not activate on the next ignition start causing warning lights to illuminate audible chimes to sound and messages to display on the instrument panel. Fix: Reprogram the Forward Recognition Camera | 4,841 |
| Nov 2023 | Affected vehicles are fitted with a high-pressure fuel pump which over time could develop a crack which could lead to a fuel leak and a risk of a vehicle fire.Fault: Affected vehicles are fitted with a high-pressure fuel pump which over time could develop a crack which could lead to a fuel leak and a risk of a vehicle fire. Fix: Check and replace high pressure fuel pump if necessary.� | 1 |
| Oct 2023 | Due to the software programming for the dcm memory capacity there is a possibility that the dcm may not complete the shutdown process within a specific period of time when the ignition is turned off causing the dcm to not restart at the next ignition cycle and making the e-call function unavailable.Fault: On affected vehicles there is a possibility that the DCM may not complete the shutdown process within a specific period of time when the ignition is turned off causing the DCM to not restart at the next ignition cycle and making the e-Call function unavailable. As a result the vehicles do not comply with relevant regulations. Fix: The software of the DCM (Data Communication Module) will be updated via an Over the Air (OTA) wireless update. | 29,827 |
| Aug 2023 | Dc-DC converter may have been damaged during productionFault: The plug-in hybrid system of the subject vehicles includes a DC-DC converter that reduces the voltage of the electricity from the Hybrid Vehicle (HV) battery in order to charge the vehicle�s 12V battery. Contained within the DC-DC converter is a current rectifying module that is installed on the circuit board. Some of these modules may have been damaged during production by the supplier and could fail so creating a short circuit. This allows current from the 12V battery to continue to flow through the module and the module will generate heat. Under certain conditions if excessive heat is generated components within and outside the DC-DC converter could sustain thermal damage increasing the risk of a vehicle fire. Fix: Replace the DC-DC Converter. | 891 |
| Jan 2023 | Fuel tank vent tube assembly could develop a crack which could lead to a fuel leak and a risk of a vehicle fire.Fault: Fuel tank vent tube assembly could develop a crack which could lead to a fuel leak and a risk of a vehicle fire.� Fix: Replace fuel tank vent tube assembly. | 207,700 |
| May 2022 | Certain spot welds might be missing.Fault: With body panels that are spot-welded to the left and right front shock absorber mounting areas there is a possibility that certain spot-welds were missed. Fix: Inspect the welding near the shock absorber mounting area. If any missing spot-weld is found welds will be added and damage to the vehicle if any will be repaired. | 759 |
| Nov 2021 | The emergency calling system (ECALL) may not function when requiredFault: The emergency calling system (eCall) may not function when required. Fix: Inspect the emergency calling system and update DCM software. If the DCM is found to be damaged replace it with updated software. | 4,092 |
| Oct 2020 | Fuel pump impeller can crack and cause fuel pump to become inoprativeFault: On affected vehicles the low pressure fuel pump located in the fuel tank could become inoperative. Fix: Replace the fuel pump. | 230,758 |
| Nov 2019 | The gas in the back door damper stay may leakFault: The damper stays may not keep the back door open Fix: Inspect and replace the stays if necessary | 165 |
| Nov 2019 | Brake booster pump may stop workingFault: An electrical connection within the motor may cause the brake booster pump to stop operating. Fix: Inspect and replace the brake booster pump assembly if necessary. | 912 |
| Aug 2019 | Possible crack could develop on the sidewall reinforcement layer of the run-flat tyresFault: Due to an improper assembly process a crack could develop on the sidewall reinforcement layer of the tyre. Fix: Replace affected tyres. | 79 |
| May 2019 | The emergency calling system may not be enabledFault: There is a possibility that the emergency calling system has not been activated. Fix: Inspect and activate the emergency call system if necessary. | 2,402 |
| Jan 2019 | Front passenger air bag inflators containing degraded propellant may result in an inflator ruptureFault: Passenger air bag may cause injury if activated. Fix: Replace affected air bag assembly. | 1,842 |
| Oct 2018 | Due to improper programming in the ECU possible loss of motive power and the hybrid system will shut downFault: loss of motive power when the accelerator pedal is quickly depressed. Fix: Reprogram the HV control ECU. | 147 |
| Apr 2018 | Fuel may leakFault: Under certain operating conditions resonance caused by fuel pressure could damage the pulsation damper in either of the high pressure fuel pumps. This damage can lead to abnormal noise/vibration and over time can cause the pump cover to develop a fatigue crack and fuel may leak. Fix: On affected vehicles replace the high pressure fuel pumps with a nev version. | 1,179 |
| Jan 2018 | Possibility of a fuel leakFault: There is a possibility that the resin weld between the fuel tank and the fuel inlet pipe may be insufficient because the fuel tank and fuel inlet pipe were misaligned during the manufacturing process. Fix: On affected vehicles replace the fuel tank with a correctly manufactured version. | 791 |
| Jan 2017 | Parking brake may not activate correctlyFault: It has been identified that due to the incorrect programming of the Brake Control Module there is a possibility that the parking brake may not be set automatically when the Brake Hold or Hill Assist System is deactivated by certain conditions for example the unfastening of the driver�s seat belt while the system is enabled. When this occurs the system is designed to deactivate the brake hold function sound a warning buzzer display a message in the instrument cluster and automatically set the parking brake. If this should occur and the transmission is left in a gear other than Park then the vehicle could creep forward or backward increasing the risk of a collision. Fix: Recall all the affected vehicles and reprogramme the Brake Control Module with the new correct software. | 18,226 |
| May 2016 | Risk of fireFault: The fuel pressure sensor may not have correctly tightened during assembly. Over time this may affect the seal and allow fuel odour to escape. This could ignite in the presence of an ignition source. Fix: On affected vehicles replace seal and tighten pressure sensor to specification. | 21,916 |
| Jul 2015 | Loss of stabilityFault: The subject vehicles are equipped with the Anti-Lock Braking system (ABS) Traction Control System (TRAC) and Vehicle Stability Control System (VSC) which are controlled by the ABS actuator. Due to the improper shape of a component inside the ABS actuator there is a possibility that a resin component could be damaged during its press fitting assembly creating minute resin fragment(s) which could become stuck in the actuator. If this occurs the oil pressure control may be delayed when the Anti-Lock Brakes are activated causing a loss of vehicle stability and increasing the risk of a crash. Fix: Recall the vehicles that are likely to be affected and where necessary replace the ABS Actuator with a new one. | 25 |
| Nov 2014 | Risk of fireFault: The fuel pressure sensor gasket may degrade and allow fuel to leak into the engine compartment. In the presence of an ignition source the risk of fire is increased. Fix: Recall the vehicles that are likely to be affected to repair the fuel pipe and replace the fuel pressure sensor gasket. | 145,680 |
| Oct 2013 | Vehicle could suddenly stopFault: It is possible that due to variations in the build specification of the Intelligent Power Module (IPM) which includes the Insluted-Gate Bipolar Transistors (IGBT's) the lead-based solder could be affected by abnormally higher operating temperatures. This could result in a degrading of the solder and eventually heat damage to the IGBT's. If this occurs then warning lights on the instrument panel will illuminate. However if the driver fails to heed these warnings or the main power supply fuse blows then the vehicle could stop without warning. Fix: Recall all the affected vehicles and replace the IPM unit with a upgraded unit. | 19,298 |
| Apr 2013 | Front wiper may become inoperativeFault: In the front wipers on subject left hand drive cars there is high friction at the tightening surface between the wiper arm nut and the wiper arm that could result in the nut being insufficiently tight. If the movement of the wiper arm is restricted by an external load such as a build up of heavy snow on the windshield the wiper motor torque may exceed the wiper arm slipping torque and one or both wipers could become inoperative. If this happens then visibility could be reduced which could increase the risk of a crash. Fix: Replace the front wiper arm nuts | 30 |
| Jan 2012 | Steering may be affectedFault: Due to a none conformance to specification the front crankshaft pulley inner and outer rubber mounted section may separate. If the separation occurs noise will become apparent the ignition warning lamp may illuminate and in the worst case the power steering drive belt may detach from the pulley which will result in the driver having to significantly increase their effort to steer the vehicle especially at low speed. Fix: Recall the vehicles that are likely to be affected to check and where necessary replace the crankshaft pulley. | 8,324 |
| Aug 2011 | Vehicle may loose powerFault: The Intelligent Power Module within the inverter system may fail. This will result in various warning lamps being illuminated. In most cases this will result in the vehicle entering the fail-safe mode resulting in limited power. In limited instances the fuse on the power supply circuit could blow resulting in the hybrid system stopping. Fix: Replacement of the Intelligent Power Module (IPM) in the inverter assembly. | 4,007 |
| Feb 2011 | Fuel may leakFault: Due to insufficient tightening of the fuel pressure sensor connected to the engine fuel delivery pipe there is a possibility that over time the pressure sensor could loosen. If loosening occurs fuel could leak past the gasket used in the connection between the sensor and pipe and through the threaded portion of the sensor. Fix: Check and retighten the fuel pressure sensor to the specified torque setting replacing the gasket if necessary. | 3,146 |
| Nov 2010 | Brake Master cylinder may fail.Fault: If the incorrect brake fluid is used in the brake system it is possible that the rear seal can become dry and curl in its recess due to the operation of the piston. This can result in a brake fluid leak which will when the fluid reaches a low level illuminate the brake fluid low warning light on the dash. Fix: Recall all affected vehicles and replace the rear seal with an improved one. | 61,780 |
Nothing matches that search on this page.
Vehicles affected is the number DVSA lists for each recall.
Lexus recalls by year
Recalls listed each year by launch date. The first bar groups all years before 2011.
How to check a car for recalls
A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.
A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.
Frequently asked questions
How do I check if my Lexus has an outstanding recall?
Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.
How many recalls have Lexus vehicles had?
DVSA's recalls data lists 41 safety recalls for Lexus vehicles since 1995, the most recent dated 1 December 2025. A recall only applies to vehicles built within set dates or VIN ranges, so check a registration with our free reg lookup to see whether that car has an outstanding recall, then confirm on GOV.UK.
Does a recall mean a car is unreliable?
No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
What should I do if my car is affected by a recall?
Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.
Where does this recall data come from?
From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.
Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.
Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.
Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.
Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.
What it can do
- ✓Free vehicle check: send any UK reg for the make, model, MOT and tax status
- ✓Send a photo of a number plate and we read the reg for you, then ask you to confirm it
- ✓Outstanding safety recall check, included in every lookup
- ✓Free valuation: add the mileage after the reg, for example 45k. A guide only, not an offer to buy or a guarantee of sale price See terms
- ✓Free MOT and tax reminders: reply REMIND with a reg (typos are fine)
- ✓Paid vehicle history check, with data provided by Experian, delivered in the chat
- ✓Find a vehicle: for example Ford Fiesta under 8k
- ✓Ask about a vehicle: send your question with the link to the vehicle on MotifyMe or its registration. Or search first, then reply ASK, the number of the vehicle and your question, for example ASK 2 is it still available. If we are not sure which vehicle you mean, we will ask
- ✓Fuel: live prices, plus a journey fuel cost such as London to Edinburgh
- ✓Fuel price alerts by email: send FUEL ALERT with your town or postcode, fuel and email address
- ✓How many are left: send HOW MANY and a model no longer sold new, for example HOW MANY Saab 9-3
- ✓Diesel driver? Send FUEL CARD for the Accelerate diesel fuel card, up to 5p a litre
- ✓Reply STOP at any time to opt out