Porsche 911 Recalls

Safety recalls covering the Porsche 911 in DVSA's recalls data, newest first.

Last updated 22 November 2026

Short answer:

DVSA's recalls data lists 38 safety recalls covering the Porsche 911, the most recent dated 19 October 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.

Check a registration for outstanding recalls, free

38Recalls listed
19 October 2026Latest recall
6 November 1992Earliest listed
18,815Vehicles affected

Every Porsche 911 recall

Open a recall to see the fault, the fix and the build dates it covers.

DateRecallVehicles affected
Oct 2026
Ata1 - wheel mounting with central wheel lock

Fault: STOP DRIVE RECALL DO NOT USE THE VEHICLE UNTIL FURTHER NOTICE TO PREVENT A POSSIBLE HAZARD. The wheel mounting with central screw connection may not meet the required specifications which can lead to damage and breakage of the central lock bolt. The wheel mounting can loosen which can result in a loss of the wheel and a loss of control over the vehicle.

Fix: The central screw connections must be checked and replaced if necessary.

Recall R/2026/395 · Dated 19 October 2026 · Built 7 June 2024 to 19 July 2024

36
Feb 2025
Asa0 - check rear SEAT belt buckles and rework if necessary

Fault: Due to a process error in the production an aluminium butyl may have been positioned incorrectly and the screw connection of the rear left and right belt buckle was potentially not executed according to the specifications. If this is the case the correct fastening of the belt buckle cannot be guaranteed. The loosening of the rear belt buckles in the event of an accident or emergency braking cannot be ruled out. This could increase the associated risk of injury.

Fix: The positioning of the aluminium butyl mat on the left and right of the affected vehicles must be checked and depending on the test result the screw connection must be reworked.

Recall R/2025/077 · Dated 26 February 2025 · Built 16 February 2023 to 13 September 2023

184
Oct 2024
Arc4 stop use & safety recall - wheel attachment with central locking

Fault: On affected vehicles the wheel attachments using the central lock may not meet the required specifications. This can lead to damage / breakage and the possibility of wheel detachment.

Fix: Check the correct functioning of the central lock wheel fastening system and replace if necessary.

Recall R/2024/427 · Dated 28 October 2024 · Built 13 September 2023 to 23 October 2024

1,104
Mar 2024
Ara3 - check front and rear windows and replace if necessary

Fault: On the affected vehicles it is possible that the front and rear window panes were not manufactured in accordance with specifications and their bonding to the body is therefore insufficient

Fix: To prevent this from happening the front and rear windows on the affected vehicles must be checked and if necessary replaced

Recall R/2024/140 · Dated 13 March 2024 · Built 9 July 2020 to 21 February 2024

2,098
Nov 2023
On affected vehicles the side airbag installed in bucket seats may be activated unnecessarily.

Fault: On affected vehicles the side airbag installed in bucket seats may be activated unnecessarily.

Fix: Recode the airbag control unit

Recall R/2023/319 · Dated 8 November 2023 · Built 15 March 2021 to 18 October 2023

1,048
Sep 2021
The screw connection of the pressure input rod of the brake booster was not carried out according to regulations

Fault: The screw connection of the pressure input rod of the brake booster may not have been tightened according to regulations.

Fix: The brake booster must be replaced or reworked depending on the vehicle type.�

Recall R/2021/317 · Dated 22 September 2021 · Built 7 November 2018 to 29 April 2021

4
Mar 2021
The threaded connections of the upper control arms at the rear axle were not tightened with the specific tigtening torque

Fault: Threaded connections of the upper control arms at the rear axle may not be tightened with the specified tightening torque.

Fix: The chassis bolts will be replaced and tightened with the specified tightening torque.

Recall R/2021/126 · Dated 24 March 2021 · Built 20 August 2019 to 17 January 2020

2
Jul 2020
The four wheel final drive screw joints to the transmission mount have not been tightened to correct specifications

Fault: The front four-wheel final drive transmission support mounts may not be tightened according to specifications.

Fix: The front-axle final drive will be removed and the transmission support will be secured according to specifications. If necessary the front-axle final drive and any other damaged components will be replaced.

Recall R/2020/211 · Dated 17 July 2020 · Built 11 December 2018 to 8 November 2019

30
Dec 2019
There is a possibility that the hazard warning lights will not be activated after pressing the centre console button

Fault: There is a possibility that the hazard warning lights will not be activated after pressing the button in the center console.

Fix: Re-program the operator control unit in front center console.

Recall R/2020/108 · Dated 13 December 2019 · Built 26 February 2019 to 5 December 2019

581
Jul 2019
Loudspeaker cover may not have been installed in the door sub frame

Fault: Possible missing cover in the door sub-frame.

Fix: Inspect retrofit cover if required.

Recall R/2019/251 · Dated 31 July 2019 · Built 12 January 2018 to 17 June 2019

1
Jul 2019
Fastening nuts to secure the drive shaft and wheel hub on the rear axle are incorrectly coated

Fault: Incorrectly coated nuts were used to secure the drive shaft and wheel hub on the rear axle.

Fix: Replace the fastening nuts and torque to specification.

Recall R/2019/207 · Dated 3 July 2019 · Built 21 January 2019 to 25 March 2019

5
Mar 2017
Incorrect detonators fitted to front passenger airbags

Fault: Incorrect passenger air bag detonators were installed during manufacturer. this may adversely affect the airbag's deployment in the event of an impact.

Fix: On affected vehicles replace the passenger's air bag module.

Recall R/2017/102 · Dated 27 March 2017 · Built 26 September 2016 to 13 January 2017

15
Mar 2017
Bonding on windscreen is insufficient

Fault: On 911 Cabriolet and Targa models only the windscreen may have been fitted with insufficient bonding product. There is a possibility that the windscreen could detach from the vehicle in the event of an accident.

Fix: Recall the likely affected vehicles and rebond the windscreen.

Recall R/2017/097 · Dated 2 March 2017 · Built 10 January 2017 to 10 February 2017

149
Feb 2017
Fuel injection pipes may become insecure

Fault: The screws retaining the fuel collection pipe(s) may shear under stress. This may allow the pipe(s) to separate from the injector(s) and cause fuel to leak.

Fix: On affected vehicle replace the collection pipes' securing screws

Recall R/2017/050 · Dated 15 February 2017 · Built 7 October 2015 to 26 September 2016

1,091
Jan 2017
Fuel may leak

Fault: The high fuel pressure that builds up in the injection system when the engine is running can cause cracking and ultimately press the relevant fuel collection pipe off the injectors. This can cause a fuel leak in the engine compartment.

Fix: Recall the vehicles that are likely to be affected and replace the fastening screws for the fuel collection pipes with different screws.

Recall R/2017/022 · Dated 25 January 2017 · Built 7 October 2015 to 26 September 2016

1,083
Jan 2017
Front side airbags may be impaired

Fault: It has been identified that the front side airbags may have been fitted with the incorrect detonators. If the vehicle is involved in a collision then the airbags may not operate as intended.

Fix: Recall all affected vehicles to replace the front side airbags with a quality assured replacement.

Recall R/2017/015 · Dated 20 January 2017 · Built 28 September 2016 to 29 September 2016

11
Oct 2016
Reduced brake performance

Fault: A vacuum supply line for the brake booster may not have been fitted correctly. The vacuum supply line could become loose resulting in reduced braking assistance. The brakes will still work but the driver will have to supply additional input for the required brake effort.

Fix: Recall the vehicles that are likely to be affected where the connection points of the vacuum supply line will be checked/adjusted/replaced as necessary.

Recall R/2016/240 · Dated 14 October 2016 · Built 7 September 2016 to 28 September 2016

140
Nov 2014
Bonnet catch assembly may fail

Fault: On affected vehicles the upper part of the catch mechanism fitted to the front luggage compartment lid may not be secured to the correct specification. The mechanism may become detached from the lid allowing it to open unintentionally.

Fix: Replace upper part of catch mechanism and secure with new screws

Recall R/2014/151 · Dated 3 November 2014 · Built 5 May 2014 to 6 June 2014

378
May 2014
Fire may occur

Fault: One or more engine con rod bolts may fail and lead to the crankcase being damaged and in the worst case fire.

Fix: Recall the vehicles that are likely to be affected to replace the engine and vehicle specific identification stickers.

Recall R/2014/059 · Dated 1 May 2014

168
Apr 2013
Tailpipe may become detached

Fault: Internal tests have shown that rear mufflers (silencer) installed on these vehicles do not achieve the required service life. As a result the exhaust tailpipe of the rear muffler can crack on vehicles with higher mileage this can result in the loss of the exhaust tailpipe and represents a danger to other road users

Fix: Replace both rear mufflers.

Recall R/2013/032 · Dated 25 April 2013

560
Dec 2012
Rear hub may detach

Fault: Current market observations have shown that the track usage of many vehicles in the 911 model line now comes close to that of pure GT3 racing vehicles. The component stresses associated with race track use and competitive driving are much higher than for a sporty driving style on public roads. The revision intervals for race track use must be observed particularly for highly stressed chassis components in the same way as is required for GT3 racing vehicles. If these revision intervals are not observed the failure of highly stressed components and breakage of hubs on the rear axle for example cannot be ruled out particularly in the case of components in advanced stages of wear.

Fix: In order to standardise revision intervals the wheel hubs on the rear axle will be replaced by standard wheel hubs on the affected vehicles with central wheel lock

Recall R/2012/156 · Dated 10 December 2012

76
Mar 2012
Risk of fire

Fault: A fuel pipe quick connector located under the vehicle could be contacting a heating pipe. The contact of the pipe and connector could impair the locking function of the connector and in the worst case could cause the fuel pipe to leak and the possibility of the engine cutting out or fire.

Fix: Recall the vehicles that are likely to be affected to check for contact of the heating pipe and fuel line and if there is sufficient clearance fit a spacing ring and if there has been contact fit a new fuel line and spacer.

Recall R/2012/040 · Dated 28 March 2012

734
May 2011
Wheel may detach

Fault: At a recent 24 hour race at the Nurburgring Circuit it was identified that the clamping force/torque on the centre wheel locking components is incorrect. If the vehicle is used under racing type conditions it is possible that the centre locking device could undo which if not identified could lead to a wheel detachment.

Fix: Recall all the affected vehicles to check the centre locking components and replace them if required.

Recall R/2011/133 · Dated 9 May 2011

430
Jan 2009
Engine spacers may detach

Fault: Due to vibration it is possible that stress cracks make occur on the engine spacer. This will normally result in noises however it is possible on high milage vehicles for the spacers to become detached.

Fix: Fitment of additional damping elements to reduce the vibration and overcome the issue.

Recall R/2009/001 · Dated 1 January 2009

434
Oct 2008
Steering could be impaired

Fault: It has been identified that it is possible that the threaded joints on the chassis of subject vehicles may not have been tightened to the prescribed torque. This may result in the screws becoming loose resulting in noises from around the vehicle. Should the screws detach steering control can become impaired.

Fix: Recalled vehicles will have the subject joints checked to ensure that they are tightened to the correct torque.

Recall R/2008/145 · Dated 9 October 2008

64
Dec 2007
Defective switch console

Fault: The switch console for the PASM (Porsche Active Suspension Management) and TC Off (Traction Control) may be defective and give incorrect signals or cause the above systems to fail.

Fix: Recall the vehicles that are likely to be affected to check and where necessary replace the switch console.

Recall R/2007/179 · Dated 12 December 2007

40
Mar 2007
Seat buckle may not de-latch following an impact

Fault: It has been identified that the possibility exists that a faulty seat belt buckle has been installed as part of the six- point seat belt harness. If a faulty buckle has been installed it may not be possible open the buckle following an accident if the belt straps have been subject to a tensile load thus requiring the seat belt straps to be cut before the occupant could leave the vehicle.

Fix: Subject vehicles will have the seat belt buckle checked for the production date and replaced as necessary.

Recall R/2007/056 · Dated 26 March 2007

48
Jan 2006
Parking brake may fail

Fault: A bearing flange on the parking brake lever is likely to break. If this occurs the parking brake will be ineffective.

Fix: Recall the vehicles that are likely to be affected and replace the parking brake lever assembly.

Recall R/2006/014 · Dated 24 January 2006 · Built 22 November 2005 to 13 December 2005

111
Jan 2006
Weld seams on the exhaust tailpipe may fail

Fault: The welded seams on the exhaust tailpipe may fail. This can cause rattling noises while driving and can result in the loss of the exhaust tailpipe if the driver continues to drive the vehicle.

Fix: Recall the vehicles that are likely to be affected and replace the exhaust tailpipes with modified units.

Recall R/2006/007 · Dated 19 January 2006

2,566
Mar 2005
The locking mechanism for Convertible top may fail

Fault: There is a possibility that when the convertible top is closed the convertible top is not completely locked even though the warning lamp is extinguished. This could lead to the roof opening whilst the vehicle is in motion.

Fix: Recall the vehicles that are likely to be affected and fit modified locking-mechanism motors. In addittion check that the correct locating pegs are installed and that the convertible top is set correctly.

Recall R/2005/009 · Dated 29 March 2005 · Built 1 February 1994 to 1 February 1998

1,612
May 2004
Seat backs do not meet the rigidity of porche specification

Fault: Front seats are fitted with seat backs that do not meet the rigidity Porsche AG demands.

Fix: Recall affected vehicles and replace the front seats with those which meet all the appropriate requirements.

Recall R/2004/063 · Dated 18 May 2004

519
Nov 2003
Possible fire risk

Fault: A connector bolt may be loose which could cause a steering fluid leak and loss of power assistance to the steering and and on the 911 Turbo to the power assistance to the clutch. Leaking fluid may ignite if it comes into contact with the exhaust system.

Fix: Vehicles must be recalled and the connector bolts must be tightened with the correct torque.

Recall R/2003/175 · Dated 17 November 2003

303
Feb 1996
Insecurity of tail pipe cover sleeve

Fault: The cover sleeve on the exhaust tail pipe may have been attached by two instead of four spot welds. There is therefore a possibility that the cover sleeve could detach from the tail pipe whilst driving.

Fix: The affected vehicles will be recalled to Porsche dealers for inspection. Any tail pipes where the cover sleeves are attached by two welds will be replaced with four weld version pipes.

Recall R/1996/024 · Dated 19 February 1996 · Built 1 January 1996 to 31 December 1996

18
Aug 1994
Possible cracking of rear axle side parts

Fault: Crack like surface defects may be present on the mould parting line on the rear axle side parts.

Fix: Recall the affected vehicles and inspect the rear axle side parts for surface defects where these are present the original side part(s) will be replaced with quality assured parts.

Recall R/1994/045 · Dated 4 August 1994 · Built 1 January 1994 to 31 December 1994

11
Apr 1994
Rear wheel lock up under braking

Fault: Under extreme circumstances rear wheel lock up could occur during heavy braking. This is due to the fitment of an incorrect brake modulator valve.

Fix: Recall the affected vehicles and replace the original brake modulator valve with a modified example.

Recall R/1994/013 · Dated 5 April 1994 · Built 1 January 1991 to 31 December 1992

258
Feb 1994
Rear heater blower resistor may overload

Fault: The rear heater blower resistor can become electrically overloaded due to binding or seizure of the heater blower. The overloaded resistor may become hot enough to ignite the plastic air pipe in which it is located.

Fix: Recall the affected vehicles for the installation of a modified resistor unit which incorporates a thermal link.

Recall R/1994/012 · Dated 16 February 1994 · Built 1 January 1989 to 31 December 1992

2,709
Aug 1993
Convertible top front locks may fracture

Fault: The front latch hooks securing the convertible top to the windscreen frame may fracture and in the worst case allow the convertible top to retract without warning whilst the vehicle is being driven.

Fix: Recall the affected vehicles for replacement of the original latch hooks with modified versions.

Recall R/1993/057 · Dated 28 August 1993 · Built 1 March 1993 to 31 March 1993

2
Nov 1992
Cruise control ball joint failure

Fault: There is a possibility that a ball socket on the cruise control may detach. This could allow the linkage to jam on adjacent components and prevent the accelerator linkage returning to the idle position when the pedal is released.

Fix: Recall the affected vehicles for replacement of the original cruise control ball sockets with quality assured steel examples.

Recall R/1993/012 · Dated 6 November 1992 · Built 1 January 1989 to 31 December 1992

192

Nothing matches that search on this page.

Vehicles affected is the number DVSA lists for each recall.

How to check a car for recalls

A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.

A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.

Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.

Frequently asked questions

How do I check if my 911 has an outstanding recall?

Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.

How many recalls has the Porsche 911 had?

DVSA's recalls data lists 38 safety recalls covering the Porsche 911, the most recent dated 19 October 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.

Does a recall mean a car is unreliable?

No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.

What should I do if my car is affected by a recall?

Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.

Where does this recall data come from?

From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.

Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.

Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.

Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.

Free vehicle check on WhatsApp

Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.

Open WhatsApp

How it works

Looking for a Porsche 911?

See used Porsche 911 cars listed on the MotifyMe® marketplace.

See 911 cars for sale