Ford Focus Recalls
Safety recalls covering the Ford Focus in DVSA's recalls data, newest first.
Last updated 22 November 2026
Short answer:
DVSA's recalls data lists 59 safety recalls covering the Ford Focus, the most recent dated 15 June 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Check a registration for outstanding recalls, free
Every Ford Focus recall
Open a recall to see the fault, the fix and the build dates it covers.
| Date | Recall | Vehicles affected |
|---|---|---|
| Jun 2026 | Transit courier: diesel dv-neo engine coolant pump updateFault: Affected vehicles may have been repaired using a coolant pump with a potential issue. This issue may lead to incorrect engine timing resulting in an engine failure causing a sudden loss of power without prior warning. The engine cannot be restarted. Fix: Check and replace the water pump and timing belt if necessary. | 8 |
| May 2026 | Multi vehicle line (MVL): telecommunications control module (TCU) loss of function software updateFault: Affected vehicles may experience a loss of emergency call system (eCall) functionality which impacts both automatic and manual eCall events. Fix: Update the Telematics Control Unit software to the latest level. | 374 |
| Mar 2026 | Focus - lane centering assist software updateFault: Certain affected vehicles may not have the remedy for Compliance Recall 24C12 installed correctly Fix: Dealers will update Audio Front Control Module (ACM) software to the latest level available. | 3 |
| Feb 2026 | Focus telematics control unit software updateFault: On affected vehicles the software repair for previous recall 20C22 may not have been delivered properly and the Telematics Control Unit (TCU) in these vehicles may disconnect from Ford's Service Delivery Network and become unresponsive. Fix: Update the TCU software and perform an additional verification process to ensure the configuration has been installed correctly. | 49 |
| Sep 2025 | Frozen rearview camera screenFault: On affected vehicles there is a potential software issue causing the rear-view camera not to function as intended. Fix: Update the Accessory Protocol Interface Module (APIM) software to the latest level. | 2,991 |
| Sep 2025 | Crosscar: SYNC3 rear-view camera software updateFault: On affected vehicles a software problem may result in issues with the rear-view camera that reduce the driver's view or with it remaining on after a reversing event. Fix: Update the vehicle software to the latest level. | 8 |
| Dec 2024 | X-car powertain control module (PCM) software updateFault: Affected vehicles may develop a crack in the Diesel Particulate Filter (DPF). Fix: Update software to prevent a cracked DPF. Test and replace DPFs that are already cracked. | 85,000 |
| Dec 2024 | Focus clutch pedal spring potential touch condition epas power supply wiringFault: On affected vehicles the clutch pedal spring may touch the Electric Power Assisted Steering wiring harness which may lead to clutch spring heat up and fall out a short circuit and loss of steering power assistance. Fix: Inspect and adjust the position of the wiring and if necessary repair any wiring damage. | 5,152 |
| Jul 2024 | Focus passenger beltminder chimeFault: While monitoring vehicles in operation we have identified a number of Focus vehicles where the passenger belt minder chime is not activated when the vehicle goes over 15 mph. Regulatory requirements mandate that an audible chime must activate when the first-row passenger seatbelt is unfastened and the vehicle speed exceeds 15 mph. Fix: Update the instrument panel cluster IPC configuration. | 1,311 |
| Jun 2024 | Focus lane centering assist software updateFault: A number of Focus vehicles have been identified where the warning chimes may not be operating as intended. The chimes may not be audible when the driver is not holding the steering wheel for longer than 30 seconds while using Lane Centering Assist which does not meet ECE regulations. Fix: Updating software in control unit. | 85 |
| Aug 2023 | On affected vehicles the lighting driver module software may be incorrectly configured which could potentially cause the adaptive headlamps to not work as intended.Fault: On affected vehicles the Lighting Driver Module software may be incorrectly configured which could potentially cause the adaptive headlamps to not work as intended. Fix: Software update and/or headlamp adjustment in order to restore feature functionality. | 96 |
| Jul 2023 | On certain vehicles tape used to protect the end of the ground connection wiring harness of the 48v battery may have become trapped beneath the nut securing the wiring harness.Fault: On certain vehicles tape used to protect the end of the ground connection wiring harness of the 48V battery may have become trapped beneath the nut securing the wiring harness. Fix: Inspect the ground connection harness. If required the tape on end of the connector will be reapplied and the nut tightened to the specified torque. | 3 |
| Jun 2023 | Certain vehicles may be fitted with a seatbelt that does not meet the high specification expected by Ford due to a rivet that is holding the buckle not being fully secured.Fault: Certain vehicles may be fitted with a seatbelt that does not meet the high specification expected by Ford due to a rivet that is holding the buckle not being fully secured. Fix: Dealers will inspect all vehicles and if found necessary will replace the part that is not meeting specification. | 2,196 |
| Aug 2022 | Vehicles could have a front suspension knuckle that was incorrectly manufacturedFault: A possibility that vehicles could have a front suspension knuckle that was incorrectly manufactured. Fix: Inspect and if necessary replace the affected components. | 179 |
| Jul 2022 | The ecall feature will stop functioning due to a malfunctionFault: It may be possible that the eCall feature will stop functioning due to a malfunction. Fix: The Telecommunication Module will need to be replaced | 9,388 |
| Jul 2022 | The garnish panel from the panorama roof may detachFault: The Garnish Panel from the Panorama roof may detach.� Fix: Test the adhesion of the panel bonding material and if necessary replace the panel.� | 12 |
| Apr 2022 | The right-hand engine oil seperator may have been damaged prior to engine assembly.Fault: Certain vehicles could have an engine oil separator that may have been damaged prior to engine assembly. Fix: Inspect the engine oil separator and if found to be damaged and/or leaking a replacement engine oil separator must be installed | 9,818 |
| Mar 2022 | The nuts on the 48v battery poles may not be torqued to specificationFault: The nuts on the 48V battery poles may not be torqued to specification. Fix: Remove both positive and negative poll nuts and inspect the wiring for signs of damage. Any damaged wiring will be replaced. Both nuts will be refitted and torqued to specification. | 17 |
| Sep 2021 | The screw which secures the ground cable of the 48v battery may not be fully securedFault: The screw which secures the ground cable of the 48v battery may not be fully secured. Fix: Replace the ground cable bolt on all vehicles and torque to specification | 11 |
| May 2021 | Vehicles may have an issue with the current software that contols the funtionality of the ecall systemFault: Vehicles may have an issue with the current software that controls the functionality of the eCall system. Fix: Carry out a software update. | 100 |
| Mar 2021 | Possible transmission stud damage to wiring loom following repairFault: Possible transmission stud damage to wiring loom following repair. Fix: Check that the correct transmission stud has been replaced. If not the correct stud must be replaced and the wiring loom should be inspected for damage and repaired as necessary. | 1,273 |
| Jan 2021 | A nut securing the MHEV battery connection may not be torqued to specificationFault: A nut securing the mHEV battery connection may not be torqued to specification. Fix: Remove the nut and inspect the wiring for signs of damage. Any damaged wiring will be replaced. A new nut will be fitted and torqued to specification in all circumstances. | 13 |
| Aug 2020 | Engine wiring loom may touch a bolt on the transmission housingFault: The engine wiring loom may touch a bolt on the transmission housing which could lead to damage to the wiring loom. Fix: Check for enough wiring loom clearance replace the clip and secure harness if not. Any damage to the wiring harness to be repaired as necessary. | 542 |
| Apr 2020 | Engine wiring loom may touch a stud on the transmission housingFault: Engine wiring loom may touch a stud on the transmission housing Fix: Transmission stud to be replaced with a bolt and rerouting of the wiring loom | 2,664 |
| Jan 2020 | A defect on the power distribution box pins may potentially cause an intermittent poor connection on a number of terminalsFault: A defect on the Power Distribution Box (PDB) pins may potentially cause an intermittent poor connection on a number of terminals. Fix: Inspect for potential damage If present replace Power Distribution Box and interfacing wiring loom pins | 4,538 |
| Nov 2019 | Seat belt anchorage bolt partially engagedFault: Seat belt anchors and seat bolts may not be secured as per specification Fix: Check tighten and torque all identified bolts to specification | 11 |
| Mar 2019 | Bolts fixing front suspension to vehicle may not be tightened to correct torqueFault: Bolts fixing the front suspension to the vehicle may not be tightened to the correct torque. Fix: The front suspension bolts must be inspected and set to the correct torque. | 22 |
| Feb 2019 | Vehicle could suffer clutch pressure plate fractureFault: A number of vehicles fitted with a 1.0 1.5 or 1.6 Ecoboost engine and 6-speed manual transmission could suffer clutch pressure plate fracture. This results in clutch smell reduced vehicle speed and performance. In the unlikely event of clutch pressure plate fracture a noise (thud / bang) could be heard from the vicinity of the transmission in extreme cases resulting in clutch / transmission fragments being released and striking under hood components creating a risk of smoke and fire from the under hood area. Fix: To prevent the repeated heating /cooling events a new calibration has been developed for vehicles fitted with Engine Stop Start feature. The software with the additional feature sets the Instrument panel �Wrench light� and de-rates the engine performance if prolonged clutch slip is detected. The software feature includes a drive cycle strategy for latching the wrench light and engine performance de-rate if the customer should experience repeated clutch slip events. For vehicles that do not have Engine Stop Start feature an alternative clutch kit has been released. | 66,497 |
| Feb 2019 | Potential for the rear doors to open when the rear windows are loweredFault: Potential for the rear doors to open when the rear windows are lowered. Fix: Ensure the door release cable is in the correct position and adjusted if necessary. | 1,729 |
| Dec 2018 | A brake pedal hinge bolt does not meet specificationFault: A brake pedal hinge bolt which does not meet specification. Fix: Check torque of brake pedal hinge bolt. If the vehicle fails the test replace the brake pedal box | 5,336 |
| Nov 2018 | Some vehicles may have an incorrectly assembled rear door latch spring that will cause the manual child lock to not function correctlyFault: Rear door latch child lock may not function correctly. Fix: Check child locks for correct activation and replace if necessary. | 3,021 |
| Jul 2018 | Clutch pressure plate may fractureFault: Affected vehicles fitted with a 1.0 1.5 or 1.6 Ecoboost engine and 6-speed manual transmission could suffer clutch pressure plate fracture. This results in clutch smell reduced vehicle speed and performance. In the unlikely event of clutch pressure plate fracture a noise (thud / bang) could be heard from the vicinity of the transmission in extreme cases resulting in clutch / transmission fragments being released and striking under hood components creating a risk of smoke and fire from the under hood area. Fix: To prevent the repeated heating /cooling events a new calibration has been developed for vehicles fitted with Engine Stop Start feature. The software with the additional feature sets the Instrument panel �Wrench light� and de-rates the engine performance if prolonged clutch slip is detected. The software feature includes a drive cycle strategy for latching the wrench light and engine performance de-rate if the customer should experience repeated clutch slip events. For vehicles that do not have Engine Stop Start feature an alternative clutch kit has been released. | 122,199 |
| Mar 2018 | Casting defect may cause alloy wheel(s) to crackFault: A small batch of alloy wheels may have a casting defect that may initiate a fatigue crack and result in wheel failure. Fix: Check wheels on affected vehicles for a specific batch code. Replace those wheels which have the identified batch code. | 80 |
| Mar 2018 | Oil sump may crack due to the engine overheatingFault: The engine control module calibration may not adequately detect an overheat condition in certain 2.0L Duratorq Diesel engines. In extreme cases an overheated engine can result in a breach of the oil sump leading to loss of the engine oil. Fix: Recall the vehicles that are likely to be affected and download revised software for the control module calibration that improves overheat detection and provides an instrument cluster warning indicator to the driver and engine de-rate strategy. | 48,595 |
| Jan 2018 | The engine cylinder head may crackFault: Localized overheating of the engine cylinder head may cause the cylinder head to crack.This may cause a pressurized oil leak which in extreme circumstances could result in a fire in the engine compartment. Fix: On affected vehicles Inspect engine and cooling system. Replace affected components and fit a Coolant Level Sensor along with associated software to provide and audible and visual warning to the driver. | 15,228 |
| Sep 2017 | Side and/or knee airbag may fail to deploy in a collisionFault: The airbag initiator may be defective and may prevent the side airbag(s) and/or knee airbag deploying in the event of an accident. In a collision the airbags not deploying could put the occupants at further risk. Fix: Recall the 1943 vehicles that are likely to be affected to check and where necessary replace the side and knee protection airbags complete with initiators. | 1,943 |
| Jul 2014 | Fire may occurFault: Engineering investigations have identified that vehicles operated in countries which have high road salt usage during winter months may experience an increased risk of corrosion build up. In extreme cases the corrosion can propagate into the electronic circuits and result in overheating. In rare cases the overheating may be sufficient to ignite the module and surrounding wiring and components. Fix: A supplemental wiring loom that removes the power supply to the fan control module when the ignition is switched off is required to be fitted to affected vehicles. An additional water shield must also be fitted to protect the module against water entry and corrosion build up. | 34,119 |
| Nov 2012 | Risk of fireFault: Due to high road salt usage in winter the engine cooling fan module may suffer from corrosion and may overheat and ignite. Fix: Recall affected vehicles to modify wiring loom and to fit water shield to module. | 1,531 |
| Jul 2011 | Risk of fireFault: Due to high road salt usage in winter the engine cooling fan module may suffer from corrosion and may overheat and ignite. Fix: Recall affected vehicles to modify wiring loom and to fit water shield to module. | 26,586 |
| Dec 2010 | Risk of fireFault: Due to high road salt usage in winter the engine cooling fan module may suffer from corrosion and may overheat and ignite. Fix: Recall affected vehicles to modify wiring loom and to fit water shield to module. | 919 |
| Aug 2010 | Risk of fireFault: Due to high road salt usage in winter the engine cooling fan module may suffer from corrosion and may overheat and ignite. Fix: Recall affected vehicles to modify wiring loom and to fit water shield to module. | 9,998 |
| Apr 2010 | Possibility of fireFault: It has been identified that a batch of vehicles converted by SVP have been fitted with a split charging system the relays of which may not be to specification and could subsequently fail. This can result in wiring loom damage and the possibility of a fire. Fix: Whereas the converter has approached 89 customers and supplied revised parts. It is proposed that Ford will contact the owners of the outstanding vehicles to emphasise the importance of end users contacting the convertor thus ensuring that the remaining vehicles are reworked. | 109 |
| Sep 2009 | Risk of fireFault: Due to high road salt usage in winter the engine cooling fan module may suffer from corrosion and may overheat and ignite. Fix: Recall affected vehicles to modify wiring loom and to fit water shield to module. | 29,325 |
| May 2009 | Hard brake pedal may occur during engine warm upFault: During engine warm up it is possible that the non return valve within the vacuum pump may stick. It is possible that if sufficient brake applications are made before the valve releases the vacuum stored within the brake booster will be used up and a hard brake pedal and longer stopping distances may result. Fix: Recall the vehicles that are likely to be affected to fit a revised design of non return valve to the brake vacuum pump. | 13,029 |
| Apr 2009 | Risk of fireFault: It has been identified that due to a specification change to the engine cooling fan module vehicles operated in countries which have high road salt usage during the winter months may experience an increased risk of corrosion build up. In extreme cases the corrosion can penetrate the electrical circuits and result in overheating. In rare cases the overheating may be sufficient to ignite the cooling fan control module and surrounding wiring whilst the vehicle is parked. Fix: Recalled vehicles will be fitted with a supplementary wiring loom that removes the power to the fan control module when the ignition is switched off. Additionally a further water shield will be fitted to protect the module against water entry and corrosion build up. | 22,325 |
| Jul 2008 | Failure of power steering hose could result in an engine bay fireFault: It has been identified that a batch of vehicles may have been fitted with section of power assisted steering hose that is not to specification. This could result in premature failure of the hose with loss of steering assistance and in extreme cases the possibility of an engine bay fire occasioned by escaping hydraulic fluid coming into contact with hot components. Fix: Recalled vehicles will have the subject hose production code checked. The hose will be changed should it fall within the given criteria. | 29,756 |
| Apr 2008 | Rear hub bolt may become looseFault: The rear hub retaining bolts may become loose because some bolts are not to the required specification. Fix: Recall the vehicles that are likely to be affected to replace the rear hub retaining bolts with those of a revised specification. | 42,081 |
| Feb 2008 | Electronic cooling fan control module may overheatFault: In markets where salt is used on roads in winter corrosion may form and propagate into the electronic fan control module and in extreme cases may cause the module to overheat. In rare cases the overheating may be sufficient to ignite the module surrounding wiring and components. Fix: Recall affected vehicles and replace the cooling fan and motor assembly. | 8,506 |
| Dec 2007 | Roll over protection may failFault: It has been identified that on affected vehicles the roll over protection system securing bolts may either be loose or not fully tight. In this condition the roll over protection may not be fully effective in the event of a roll over occurring. Fix: Recalled vehicles will have the protection units checked for the correct number of securing bolts with bolts being installed as necessary. In addition all securing bolts will be checked to ensure that they are tightened to the correct specification. | 3 |
| Dec 2007 | In low ambient temperature hard brake pedal may occurFault: Hard brake pedal may occur in low ambient temperatures which is caused by a non return valve in the vacuum pump sticking. Fix: Recall the vehicles that are likely to be affected to fit a revised non return valve to the brake vacuum pump. | 17,972 |
| Jul 2006 | Engine may failFault: It has been identified that a batch of engines have misaligned oil feed holes between the cylinder head and the camshaft bearings. The reduced oil flow could cause premature wear of the camshaft bearings and may also result in seizure of the engine without prior warning. Fix: Recalled vehicles will be checked by dealers for the presence of the relevant build code and the engine will be renewed if it is within the specified range. | 167 |
| Aug 2005 | Wiper motor may fail and overheatFault: Water may enter the wiper motor via the wiper arm spindle. If the water contains salt it is possible that an electrical short circuit can cause the wiper to fail. In extreme cases the short circuit can result in the wiper assembly overheating. The increased temperature can be high enough to melt the trim components in the area of the motor assembly. Fix: Recalled vehicles will be fitted with a revised cover and sealing grommet which will replace the existing sealing system. | 68,996 |
| Apr 2005 | Fuel return pipe leakFault: The fuel return pipe is not specification and will degrade. This could lead to seapage of fuel. Fix: Recall the vehicles that are likely to be affected and replace the fuel return pipe. | 904 |
| Jan 2004 | Rear brake hoses may chafeFault: Left and right hand rear brake flexible hoses may chafe on the wheel arch liners. Fix: Check the brake hoses for damage and modify the rear wheel arch liners. | 30 |
| May 2002 | Alternator terminal concernFault: Alternator B+ terminal may break due to incorrect hardness leaving battery +cable loose. Fix: Dealers are to check the Alternator B+ terminal type (visual check) and where necessary replace the alternator. | 4,447 |
| May 2000 | Engine may cut-out/stallFault: Excessive crankshaft end-float may allow the torque converter to contact the crankshaft position sensor. Damage to the crankshaft position sensor may lead to engine cut-out/stall. Fix: Recall affected vehicles for fitment of a revised crankshaft thrust bearing assembly and a new crankshaft position sensor. | 3,121 |
| Mar 2000 | Oil filler cap may become looseFault: Oil filler cap may become loose resulting in oil dripping onto the exhaust heat shield. Fix: Replace oil filler cap with a new redesigned version. | 81,256 |
| Mar 2000 | Engine may lose powerFault: Engine may lose power due to a malfunction in the power train control module software. Fix: Recall affected vehicles and re-programme the power train module. | 20,577 |
| Oct 1999 | Door latch concernFault: Some vehicles have been built with door latches which may not be to specification. An internal plastic pawl within the assembly may seize which results in the latch failing to function as designed preventing the door being securely shut. Fix: Recall affected vehicles and fit quality assured replacement door latches. | 32,232 |
Nothing matches that search on this page.
Vehicles affected is the number DVSA lists for each recall.
How to check a car for recalls
A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.
A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.
Frequently asked questions
How do I check if my Focus has an outstanding recall?
Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.
How many recalls has the Ford Focus had?
DVSA's recalls data lists 59 safety recalls covering the Ford Focus, the most recent dated 15 June 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Does a recall mean a car is unreliable?
No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
What should I do if my car is affected by a recall?
Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.
Where does this recall data come from?
From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.
Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.
Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.
Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.
Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.
What it can do
- ✓Free vehicle check: send any UK reg for the make, model, MOT and tax status, plus any outstanding safety recall
- ✓Snap a number plate: send a photo and we read the reg for you, then ask you to confirm it
- ✓Free valuation: add the mileage after the reg, for example AB12 CDE 45k. A guide only, not an offer to buy or a guarantee of sale price See terms
- ✓Paid vehicle history check, with data provided by Experian, delivered in the chat
- ✓Free MOT and tax reminders: reply REMIND with a reg (typos are fine)
- ✓Recalls: send RECALLS and a make or model, for example RECALLS Ford Puma
- ✓MOT pass rates: send MOT RATE and a model, for example MOT RATE Ford Fiesta
- ✓How many are left: send HOW MANY and a model no longer sold new, for example HOW MANY Saab 9-3
- ✓Find a vehicle: tell us what you want, for example Ford Fiesta under 8k
- ✓Ask about a vehicle: send its MotifyMe link or reg with your question, or after a search reply ASK, the number and your question, for example ASK 2 is it still available
- ✓Fuel prices: live prices, plus a journey fuel cost such as London to Edinburgh
- ✓Fuel price alerts by email: send FUEL ALERT with your town or postcode, fuel and email address
- ✓Diesel driver? Send FUEL CARD for the Accelerate diesel fuel card, up to 5p a litre
- ✓Reply STOP at any time to opt out
Looking for a Ford Focus?
See used Ford Focus cars listed on the MotifyMe® marketplace.
See Focus cars for sale