Mitsubishi Outlander Recalls

Safety recalls covering the Mitsubishi Outlander in DVSA's recalls data, newest first.

Last updated 22 November 2026

Short answer:

DVSA's recalls data lists 28 safety recalls covering the Mitsubishi Outlander, the most recent dated 25 July 2021. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.

Check a registration for outstanding recalls, free

28Recalls listed
25 July 2021Latest recall
29 September 2008Earliest listed
444,472Vehicles affected

Every Mitsubishi Outlander recall

Open a recall to see the fault, the fix and the build dates it covers.

DateRecallVehicles affected
Jul 2021
If there is an object in front of the vehicle the fcm camera system may incorrectly detect it as a pedestrian depending on road circumstances.

Fault: If there is an object in front of the vehicle the FCM camera system may incorrectly detect it as a pedestrian depending on road circumstances.

Fix: Carry out a software update to the FCM-ECU.

Recall R/2021/233 · Dated 25 July 2021 · Built 5 August 2016 to 19 March 2020

17,804
Oct 2020
The right side second row SEAT belt may be assembled incorrectly

Fault: The right side second row seat belt may be assembled incorrectly.

Fix: Inspect the installation of the seat belt and replace if necessary.

Recall R/2020/146 · Dated 9 October 2020 · Built 24 June 2019 to 30 July 2019

496
May 2019
The resistor inside the air flow sensor may corrode

Fault: It may not be possible to start the engine in order to charge the main drive battery.

Fix: The air flow sensor is to be replaced on the affected vehicles.

Recall R/2019/142 · Dated 17 May 2019 · Built 1 October 2013 to 17 January 2014

12
Jan 2019
Sunroof glass may detach from the sunroof assembly

Fault: The sunroof glass may detach from the sunroof assembly.

Fix: Replace the sunroof glass and bonding material.

Recall R/2018/336 · Dated 2 January 2019 · Built 14 November 2006 to 10 July 2012

5,940
Jan 2019
The flange of the drive belt automatic tensioner may crack

Fault: Power steering drive belt automatic tensioner may crack and fail.

Fix: Replace the automatic tensioner and bolts.

Recall R/2018/335 · Dated 2 January 2019 · Built 31 March 2008 to 24 October 2009

398
Nov 2018
The brake hydraulic unit function may be interrupted

Fault: Driver assist programme functions through the hydraulic brake unit may be interrupted.

Fix: The ECU will be rewritten with modified software.

Recall R/2018/285 · Dated 3 November 2018 · Built 3 August 2016 to 22 January 2018

35,266
Nov 2018
On certain vehicles equipped with fcm fcm may activate the brake for longer than necessary

Fault: Collision avoidance system may activate the brake for longer than necessary.

Fix: The ECU will be rewritten with modified software.

Recall R/2018/286 · Dated 3 November 2018 · Built 5 August 2016 to 6 November 2017

6,752
Aug 2018
Parking brake caliper shaft boots incorrectly sealed

Fault: Due to improper sealing of parking brake caliper shaft boots water might penetrate inside and rust the shaft. As the result of continuous use the rust will erode into the internal caliper and the shaft becomes stuck causing decreased parking brake force. Due to improper manufacturing process automatic adjuster for brake pad clearance of rear brake caliper might not work properly. As the result as brake pad wear the clearance is not correctly adjusted and brake force becomes insufficient to hold a vehicle. In the worst case scenario parking brake will not work even though a lever is fully operated and parked vehicle may move.

Fix: Anti-rust coating (Fluorine) has been applied to parking brake shaft from 27/01/2016 supplied parts & the Inspection process for the caliper has been changed from 14/12/2014 supplied parts.

Recall R/2018/180 · Dated 8 August 2018 · Built 11 September 2012 to 12 April 2016

204,616
May 2018
Water ingress may cause windscreen wipers to fail

Fault: Due to inappropriate waterproofing water may be drawn into the front wiper motor and/or may cause corrosion of the wiper link ball joint. This may over time cause the wipers to fail.

Fix: On affected vehicles replace the wiper motor which has a modified breather and wiper link ball joint.

Recall R/2018/117 · Dated 26 May 2018 · Built 14 November 2006 to 10 July 2012

13,819
Feb 2018
Door latching mechanism may malfunction in hot temperatures

Fault: The locking mechanism in the door latch assembly may not operate properly in high temperatures. As a result the door may latch correctly and may unintentionally open whilst driving.

Fix: A modified assembly is available and depending on vehicle identification number the remedy is to replace either both O/S door latches or on all four doors.

Recall R/2018/021 · Dated 19 February 2018 · Built 6 May 2015 to 15 March 2016

36,836
Feb 2018
Ecu Relay may overheat and cause ECU to malfunction

Fault: The engine Electronic Control Unit Relay may overheat and fail. This could interrupt power supply to the engine and will cause the engine malfunction warning lamp to illuminate. The engine may stall and may not restart.

Fix: On affected vehicles the engine ECU power relay will be replaced with a new relay.

Recall R/2018/019 · Dated 19 February 2018 · Built 5 December 2014 to 6 April 2016

56,118
Jul 2017
Internal combustion engine may not perform as expected

Fault: The Internal Combustion Engine may not operate correctly. DTC�s will be generated the engine-warning lamp will illuminate and the combination meter will display a message. In the worst case the internal combustion engine will fail to start and charge the main traction battery. If the warnings are ignored the main traction battery will become depleted and the vehicle will lose all drive.

Fix: Recall the vehicles that are likely to be affected and apply countermeasure software to the ECU and replace the spark plugs with ones of approved specification.

Recall R/2017/183 · Dated 3 July 2017 · Built 1 October 2013 to 1 June 2015

14,242
Nov 2015
Fuel may leak

Fault: There is a possibility that a connection of the fuel pipe to the fuel hose has been improperly mounted in production

Fix: On affected vehicles inspect the installation of the fuel hose connector and if found to be improper remove and reconnect correctly

Recall R/2015/220 · Dated 17 November 2015 · Built 21 July 2015 to 12 September 2015

1,092
Sep 2015
Ecu malfunction may cause systems to become inoperable

Fault: During operation the headlights and or the windscreen wipers amongst other systems may become inoperable as a result a none conformity in the Electronic Time & Alarm System (ETACS) ECU.

Fix: Recall the vehicles that are likely to be affected and check the production date of the ETACS ECU. The ETACS ECU will be replaced if it is within the affected production dates.

Recall R/2015/157 · Dated 28 September 2015 · Built 1 October 2008 to 7 September 2010

3,076
Nov 2014
Loss of power steering assistance

Fault: Due to the use of inappropriate material for the drive belt on the 4B1 Petrol engine the nylon idler pulley(s) may wear at an angle. If this continues under this condition the drive belt will be forced off the pulleys. This can lead to battery depletion Overheating and on vehicles with hydraulic power steering the steering effort will increase.

Fix: Replace drive belt. Check and if necessary replace idler pulley(s)

Recall R/2014/124 · Dated 28 November 2014 · Built 10 September 2007 to 24 September 2009

3,885
Nov 2014
Brake lamps may not illuminate

Fault: Silicon grease applied to the brake light switch during production may penetrate the switch and insulate the contacts. This may prevent the stop lamps from operating and on vehicles with automatic transmission the shift lever cannot be moved from the park position.

Fix: Clean mounting and replace brake light switch

Recall R/2014/109 · Dated 28 November 2014 · Built 24 January 2007 to 13 October 2009

7,070
Nov 2014
Brake pedal fails to release

Fault: Due to incorrect installation of the switch sleeve in the brake booster the switch sleeve may be cracked. As a result the tip of the switch sleeve could break off causing the brake pedal not to release with the effect of the vehicle being unable to restart/move/pull away.

Fix: Recall the vehicles that are likely to be affected to check the production date of the brake booster. Replace the brake booster if it is of the affected production dates.

Recall R/2014/129 · Dated 28 November 2014 · Built 20 August 2010 to 10 July 2012

8,666
Jul 2014
Possible loss of drive

Fault: As a result of incorrect machining of the oil seal installation aperture in the transfer cover by one of the transfer box suppliers it is possible the oil seal may move from its intended position in the casing. This can result Automatic Transmission Fluid (ATF) passing from the main gearbox into the transfer casing causing the ATF pressure to drop which will result in poor shifting and the illumination of a warning lamp on the instrument panel. Also as the oil level in the transfer box increase it can leak out from the transfer box breather pipe onto the road surface. In the worst case scenario the vehicle can lose all drive.

Fix: Recall all affected vehicles to inspect the transfer box. If found to be one of the affected transfer boxes then the transfer box will be replaced.

Recall R/2014/072 · Dated 25 July 2014 · Built 1 September 2012 to 2 April 2013

574
May 2014
Reduction in power steering assistance

Fault: Due to a nonconformity in the manufacture of the alternator pulley (free wheel type) the contact surface of the pulley might be deformed. In use the tightening torque of the alternator pulley can decrease resulting in the pulley detaching from the alternator. Should this happen the driver will notice reduced power steering assistance and the warning lamp for the charging system will illuminate.

Fix: Recall the vehicles that are likely to be affected and ascertain which alternator is fitted. Where an unmodified alternator is fitted replace the alternator.

Recall R/2014/044 · Dated 21 May 2014 · Built 1 July 2010 to 31 January 2012

2,100
Jul 2013
Adaptive cruise control may fail to operate and/or cause brakes to apply

Fault: One or both of the following may occur: 1) While driving through a tunnel with the Adaptive Cruise Control (ACC) operating the ACC control unit may judge that the tunnel wall is a vehicle in front. This can result in the ACC system automatically applying the brakes to reduce vehicle speed. 2) Due to a calculation error in the ACC/Front Collision Mitigation (FCM) control unit ACC failure and Active Stability Control (ASC) failure may be displayed in the combination meter along with an audible warning alarm. The ACC and FCM systems will not operate when these warnings are displayed.

Fix: Recall the vehicles that are likely to be affected to rewrite the ACC/FCM Electronic Control Unit software with modified software.

Recall R/2013/074 · Dated 1 July 2013

385
May 2012
Parking brake may fail

Fault: It is possible that the parking brake cable may not be properly located in the rear brake shoes parking brake operating lever. It is therefore possible if the cable is not secure that the cable may become loose during driving which will result in the failure of the handbrake if not rectified.

Fix: Recall all affected vehicles to check and if required secure the cable.

Recall R/2012/068 · Dated 31 May 2012 · Built 27 April 2011 to 29 April 2011

35
Oct 2011
Rear wheel and hub may detach

Fault: The rear wheel hubs may come loose which will produce noise to warn the driver. However should the driver continue to driver the vehicle it is possible that the wheel and hub will detach from the vehicle.

Fix: Recall the vehicles that are likely to be affected to replace the hub bolts and where necessary also replace the wheel hubs.

Recall R/2011/099 · Dated 14 October 2011

174
Aug 2010
Clutch may fail

Fault: The fixing clip for the clutch master cylinder pipe has insufficient clamping force to retain the pipe on the cylinder. This can result in detachment of the pipe and subsequent loss of clutch operation.

Fix: Recall affected vehicles and replace fixing clip with modified stronger version.

Recall R/2010/080 · Dated 18 August 2010

9,903
Aug 2010
Short circuit may occur

Fault: It is possible for the engine wiring harness to chaff on a security bracket. If this is allowed to continue this could result in a short circuit in the starter motor circuit which can cause the starter to operate whilst the vehicle is being driven. This will cause the starter to overheat and possibly cause a fire.

Fix: Recall the affected vehicles to inspect and insulate the wiring if required.

Recall R/2010/079 · Dated 18 August 2010

9,369
Jul 2009
Stop lights may not operate correctly

Fault: It has been identified that as the result of the manufacturing process silicon grease may have contaminated the stop lamp switch contacts. This can result in oxidation of the contacts and prevent the stop lamps operating when the footbrake is applied.

Fix: Recalled vehicles will have the stop lamp switch replaced.

Recall R/2009/039 · Dated 15 July 2009 · Built 1 January 2007 to 31 December 2008

4,307
Jul 2009
Lack of brake servo assistance

Fault: It has been identified that after the vehicle has been stationary for some length of time increased pressure may need to be applied to the footbrake pedal to bring the vehicle to a stop. This is due to insufficient vacuum assistance within the brake booster due to a failure of the check valve. It should be noted that on the second application of the footbrake the check valve will operate as designed and the brakes will operate as normal.

Fix: Recalled vehicles will have the brake booster check valve replaced.

Recall R/2009/037 · Dated 15 July 2009 · Built 1 January 2008 to 8 April 2009

818
Sep 2008
Engine may stall

Fault: When a driver sequentially performs a quick gear shift down (high rpm 6th to 5th to 4th gear etc)during high speed driving (high engine load) the engine ECU can judge the engine to run in overrun condition. As a result to avoid engine damage the ECU will turn off the engine by stopping the fuel supply and closing the throttle.

Fix: Recall the vehicles that are likely to be affected to re-programme the engine ECU.

Recall R/2008/058 · Dated 29 September 2008

387
Sep 2008
Fuel could leak from the resin fuel return pipe on the inlet manifold.

Fault: It has been identified that the engine fuel return pipe can become damaged as the result of abrasion with it's fixation and harness.

Fix: Recalled vehicles will be checked for evidence of pipe damage which if none is evident protective covers will be installed. Should it be found that the pipes are damaged they will be replaced by pipes which are fitted with protective covers.

Recall R/2008/108 · Dated 29 September 2008 · Built 1 January 2008 to 11 July 2008

332

Nothing matches that search on this page.

Vehicles affected is the number DVSA lists for each recall.

How to check a car for recalls

A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.

A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.

Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.

Frequently asked questions

How do I check if my Outlander has an outstanding recall?

Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.

How many recalls has the Mitsubishi Outlander had?

DVSA's recalls data lists 28 safety recalls covering the Mitsubishi Outlander, the most recent dated 25 July 2021. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.

Does a recall mean a car is unreliable?

No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.

What should I do if my car is affected by a recall?

Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.

Where does this recall data come from?

From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.

Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.

Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.

Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.

Free vehicle check on WhatsApp

Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.

Open WhatsApp

How it works

Looking for a Mitsubishi Outlander?

See used Mitsubishi Outlander cars listed on the MotifyMe® marketplace.

See Outlander cars for sale