Volvo XC60 Recalls
Safety recalls covering the Volvo XC60 in DVSA's recalls data, newest first.
Last updated 22 November 2026
Short answer:
DVSA's recalls data lists 53 safety recalls covering the Volvo XC60, the most recent dated 23 June 2025. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Check a registration for outstanding recalls, free
Every Volvo XC60 recall
Open a recall to see the fault, the fix and the build dates it covers.
| Date | Recall | Vehicles affected |
|---|---|---|
| Jun 2025 | Bcm2 sw - safety noticeFault: Affected vehicles may experience a temporary loss of braking functionality after coasting downhill with 'B' mode selected or when using One Pedal Drive. This could potentially lead to a collision. Fix: Install modified software via an Over the Air (OTA) update. | 2,254 |
| Mar 2025 | Spa1 cell modulesFault: On affected vehicles the High Voltage (HV) Battery may have a manufacturing defect which could cause the battery cells to overheat when the HV Battery is fully charged. In a worst-case scenario there is a risk of fire when the vehicle is parked up with a fully charged HV Battery. Fix: Check and replace the HV Battery if necessary and install modified software. | 780 |
| Nov 2024 | Bcm2 - push roadFault: The rod connecting the brake pedal to the brake booster may not have been assembled correctly. The final torque might not be according to manufacturing specification due to deviations in the equipment. If the rod does disconnect the mechanical connection between brake pedal and brake booster cannot be guaranteed. In the worst-case scenario if the rod disconnects the brake pedal function cannot be guaranteed Fix: A Volvo retailer will check and if necessary tighten the rod to correct specification. | 970 |
| Mar 2024 | Seat and SEAT belt torqueFault: The screw joints for the seats and seat-belts may not have been torqued to the correct specification which means in the event of an impact insufficient protection will be available. Fix: The solution is to check and adjust the torque. | Not stated |
| Jan 2023 | There may be a potential software error in the brake control module.Fault: There may be a potential software error in the brake control module. Fix: Update the brake control module software. | 10,197 |
| Oct 2022 | A software error may prevent the engine control module from starting the engineFault: The Engine Control Module (ECM) may prevent the combustion engine from starting.� Fix: Download updated software. | 4,755 |
| Oct 2021 | Thrust bearing in turbo charger might not be robust enoughFault: The thrust bearing in the turbo charger may not be robust enough. Fix: Replace turbocharger with a modified version which has an improved thrust bearing. | 2,083 |
| Sep 2021 | Potentially insufficient or missing welding connection in the hydraulic unit of the brake systemFault: There may be an insufficient or missing welding connection in the Hydraulic Unit of the Brake System. Fix: Replace the Hydraulic Unit. | 28 |
| Jun 2021 | There is a risk that the 15amp fuse could blow which will prevent the low pressure fuel pump from operatingFault: There is a risk that the 15amp fuse could blow which will prevent the low pressure fuel pump operating. Fix: Replace the 15A fuse with a 20A fuse which can withstand this peak. | 14,380 |
| Jan 2021 | Vehicles may have the supplementary restraint system control unit incorrectly tightened to the car bodyFault: Vehicles may have the Supplementary Restraint System (SRS) control unit incorrectly tightened to the car body. Fix: Inspect and tighten the SRS control unit. | 704 |
| Aug 2020 | Front wiper arm securing nuts may be incorrectly tightenedFault: Vehicles may have incorrectly tightened front wiper arm securing nuts Fix: Check and tighten the nuts to an increased torque setting. | 31,778 |
| Jul 2020 | There is a risk for trapped air to be in the cooling system which may result in insufficient cooling of engine componentsFault: There is a risk for trapped air to be in the cooling system which may result in insufficient cooling of engine components. Fix: Add an extra degassing line (Bleeder Hose) between the cooling system radiator and the cooling system expansion tank which will evacuate the trapped air | 76,945 |
| Jul 2020 | There is a risk for trapped air to be in the cooling systemFault: There is a risk for trapped air to be in the cooling system which may result in insufficient cooling of engine components. Fix: Add an extra degassing line (Bleeder Hose) between the cooling system radiator and the cooling system expansion tank which will evacuate the trapped air. | 15,167 |
| Jul 2020 | Potential breakage/fatigue of a flexible steel cable supporting the front seatbelt anchor pointFault: Potential breakage/fatigue of a flexible steel cable supporting the front seatbelt anchor point. Fix: Replace the seat belt fastener with a new designed seat belt fastening. | 170,160 |
| Mar 2020 | Software issue means that automatic emergency brake system may not engageFault: The Automatic Emergency Brake System a function of the IntelliSafe system may not always engage increasing the risk of a collision Fix: Affected vehicles must have new software downloaded | 56,385 |
| Dec 2019 | Possible loss of power whilst drivingFault: Possible loss of power whilst driving. Fix: Vehicles must have updated software downloaded. | 53 |
| Oct 2019 | The engine's plastic inlet manifold may melt and deformFault: The engines plastic inlet manifold may melt and deform Fix: Update vehicles with improved soot reducing software cleaning of TMAP and EMAP. Fit additional hoses where necessary. | Not stated |
| Jan 2019 | The tailgate lifting arms may freezeFault: Under certain conditions in cold climates the tailgate lifting arms may freeze and separate. Fix: Replace both lifting arms on the tailgate. | 13,273 |
| Jan 2019 | Small cracks on the inside of a rubber fuel hoseFault: Small cracks on the inside of a rubber fuel hose. Fix: Replacement of affected fuel hoses. | 30,777 |
| Nov 2018 | Possible software issue in the vehicle connectivity module (VCM)Fault: There may be a software issue in the Vehicle Connectivity Module. Fix: Upgrade software in the Vehicle Connectivity Module. | 7,322 |
| Jan 2017 | One or more airbags may fail to deploy in the event of a collisionFault: It has been identified by the manufacturer that the air-bag initiator does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to none deployment of the air-bag. Should a collision occur then there is an increased risk of injury to the occupants of the vehicle. Fix: Recall all affected vehicles to replace the air-bags with a new quality assured component. | 1,415 |
| Nov 2016 | Seatbelt may separate from the buckleFault: It has been identified there is a possibility the front seatbelt buckle stud may not have been punched correctly during production. This may result in a separation between the buckle and seatbelt bracket if the vehicle is involved in a collision. Fix: Recall all affected vehicles to inspect the seatbelt buckle and if required to replace the seatbelt buckle. | 47 |
| Jun 2016 | Driver's airbag module may not deploy as intendedFault: Due to a potential manufacturing defect the gas generator in the driver�s airbag module may not deploy as intended. This may reduce the affectivities of the airbag. Fix: On affected vehicles replace the driver's air bag module. | 123 |
| Feb 2016 | Stalling and loss of steering power assistanceFault: Involved vehicles may have a software issue which could cause the engine to momentarily cut-out and restart while driving. This could also cause disturbances in some electrical systems such as shut down of the instrument cluster infotainment system and loss of power steering assistance. Fix: Recall the vehicles that are likely to be affected and upgrade the software of the control units. | 7,237 |
| Jan 2016 | Fuel guage may not show fuel level correctlyFault: Fuel gauge may not show correct level Fix: The remedy is not yet available for all models. Until a remedy is available the manufacturer advises to maintain fuel level above approx one third. | 1,109 |
| Dec 2015 | Fuel guage may not show fuel level correctlyFault: Fuel gauge may not show correct level Fix: The remedy is not yet available for all models.. Until a remedy is available the manufacturer advises to maintain fuel level above approx one third. | 2,743 |
| Dec 2015 | Fuel guage may not show fuel level correctlyFault: Fuel gauge may not show correct level Fix: Dependent on affected Model update software. Until updated the manufacturer advises to maintain fuel level above approx one third. | 5,354 |
| Oct 2015 | Engine may failFault: Affected vehicles may have a crankshaft that has been insufficiently hardened which may fail and nay cause engine failure. Fix: Check identity of crankshaft. If the relevant marking is not present then replace engine. | 9 |
| Oct 2015 | Engine may failFault: The crankshaft may not have been sufficiently hardened and may fail this in turn can lead to sudden and catastrophic engine failure. The failure may be preceded by loss of power and a knocking noise. Fix: Recall the vehicles that are likely to be affected and replace the engine. | 5 |
| Feb 2015 | Parking brake may unintentionally releaseFault: Vehicles with manual gearboxes and start/stop functionality have Parking Brake Module (PBM) software that may allow the parking brake to unintentionally release. The unintended release of the parking brake can only occur when the engine is running and the gearstick moved so it will happen when the vehicle is attended. Fix: Recall the vehicles that are likely to be affected to download upgraded Parking Brake Module (PBM) software. | 2,146 |
| Nov 2013 | Loss of power steering assistanceFault: The auxiliary drive belt tensioner can suffer from premature wear which may cause it to fail. This can lead to loss of steering power assistance and a slight possibility of loss of drive should the drive belt or tensioner invade the cambelt area. Fix: Recall the vehicles that are likely to be affected to replace the auxiliary drive belt and tensioner. | 3,134 |
| Apr 2012 | Engine may failFault: There could be a sudden and unexpected failure of the bottom end of the engine because of a non-conformity during production of the connecting rods. Fix: Recall the vehicles that are likely to be affected to replace the engine. | 6 |
| Mar 2012 | Fuel may leakFault: Some vehicles may have had excessive underbody protection applied which when drying. could have formed small stalactite shaped formations. These formations may have formed close to the underbody fuel lines and could damage them and cause a fuel leak. Due to the positioning of the fuel lines escaping fuel or fuel vapour could potentially lead to a fire. Fix: Inspect all vehicles and cut any stalactite shaped formations off. If the fuel line is damaged it will be replaced. Only 1% of vehicles are expected to have any damage to the fuel line. | 481 |
| Mar 2012 | Airbags may not deploy in a collisionFault: It has been identified that the wiring harness for the SRS system may not have been correctly attached to the front seat frames. It is possible that continued adjustment of the seat position may cause the harness to become detached. If this should occur a warning light will illuminate on the instrument panel warning the driver of a fault with the SRS system. However in this condition the front and side airbags may not deploy if the vehicle is involved in a collision. Fix: Recall all affected vehicles for an inspection of the wiring harnesses and ensure that it is correctly routed and secured. If not then reroute and securing of the wiring harness. | 9,330 |
| Dec 2011 | Engine may loose drive and power steering assistance.Fault: The auxiliary drive belt tensioner may fail. This can lead to loss of steering power assistance and a slight possibility of loss of drive should the drive belt or tensioner invade the cambelt area. Fix: Recall the vehicles that are likely to be affected to replace the auxiliary drive belt and tensioner. | 7,302 |
| Oct 2011 | Possibility of loss of driveFault: The auxiliary drive belt tensioner may fail. If the tensioner fails it would cause a loss of power steering assistance and possible loss of drive. Fix: Replace the auxiliary drive belt tensioner. | 9,936 |
| Jan 2011 | Engine may run onFault: It is possible in certain circumstances for the engine oil level to rise above the maximum level. This situation could lead to engine speed being maintained or possibly increased after the throttle pedal is released. In extreme cases the engine could continue to run after it has been switched off. Fix: Recall the vehicles that are likely to be affected to adjust the engine oil level and carry out a software upgrade. | 4,787 |
| Dec 2010 | Passenger SEAT may not be fitted correctlyFault: It is possible that the driver's and passenger's front powered seats may not be fitted with the front stop lug. The lug restricts the movement of the seats and if not fitted it is possible to position the seats too far forward or backwards. This could increase the chances of injury should the vehicle be involved in an accident. Fix: Recall all affected vehicles to inspect for fitment of the lugs and if found to be missing fit new lugs. | 103 |
| Dec 2010 | Fire may occurFault: On certain five cylinder engines it is possible that the high pressure fuel pipes may not have been correctly installed and may leak. This should be identified by a smell of fuel from the engine bay. However it is possible that in extreme cases an engine bay fire could occur. Fix: Recall all affected vehicles and replace the high pressure pipes. | 845 |
| Nov 2010 | Engine may cut outFault: When driving at low speeds a fault within the software calibration of the engine and transmission control modules may lead to a drop in the engine idle speed when braking or releasing the accelerator. In extreme cases this may result in the engine cutting out without warning. Fix: Recall the vehicles that are likely to be affected to upgrade the engine/transmission software. | 64 |
| Nov 2010 | Airbag curtain may not deploy correctlyFault: The inflatable curtain may have been fitted incorrectly which could prevent it from deploying as intended. Fix: Recall the vehicles that are likely to be affected to check and where necessary adjust the curtain. | 20 |
| Nov 2010 | Engine speed may increase without warning.Fault: It is possible that the engine oil level may rise above its maximum level due to overfilling and/or dilution by fuel. This may result in the engine speed being maintained or possibly increased after the throttle pedal has been released. In extreme cases it is possible that the engine may continue to run after it has been switched off. Fix: Recall all affected vehicles and carry out an Engine Control Module software upgrade and adjust the engine oil. The new ECM upgrade will improve adaption of different blends of fuel and include a dashboard text warning message if the oil level reaches too high a level. | 4,430 |
| Oct 2010 | Airbag may not deploy as intended.Fault: It is possible that an electrical short circuit within a connector could result in the illumination of the Airbag System Service Required message and Supplemental Restraint System warning lamp on the dashboard. Should this occur the driver's airbag would not deploy as intended if the vehicle is involved in a collision. Fix: Recall all affected vehicles to check and rework the connector. | 6,844 |
| Jul 2010 | Engine may seizeFault: On effected petrol and diesel engines a spring clamp on the radiator hose connecting it to the water inlet pipe may be insecure. If not rectified the engine may lose coolant overheat seize and suddenly slow the vehicle rapidly to a halt. Fix: Recall the vehicles that are likely to be affected to have the radiator hose adequately secured. | 326 |
| Jun 2010 | Gearbox may jamFault: A section of the gear shift mechanism may over time become loose and cause the mechanism to become jammed. If this was to occur it might not be possible to change gear or select neutral. Fix: Recall the vehicles that are likely to be affected to check that the ball joint for the gear selector is properly secured. | 6,961 |
| May 2010 | Engine may loose drive and power steering assistance.Fault: The auxiliary drive belt tensioner may fail. This can lead to loss of steering power assistance and a slight possibility of loss of drive should the drive belt or tensioner invade the cambelt area. Fix: Recall the vehicles that are likely to be affected to replace the auxiliary drive belt and tensioner. | 4,673 |
| May 2010 | Engine speed may not decreaseFault: The engine oil level may rise. This situation may lead to the engine speed being maintained or possibly increased after the throttle pedal is released. In an extreme situation the engine may continue to run after it has been switched off. Fix: Recall the affected vehicles and carry out a ECM software upgrade adjust engine oil level and install a decal to confirm oil level to the consumer. | 20,204 |
| Mar 2010 | Power steering fluid may leak - risk of fireFault: It has been identified that a joint between the power steering high pressure lines and the steering gear may not have been assembled correctly. This may result in a power steering hydraulic fluid leak and a sudden loss of steering assistance. Due to the pressure within the hydraulic system hydraulic fluid may be sprayed onto the engine with the attendant risk of fire. Fix: Recalled vehicles will check the subject joint and if necessary replace any cross threaded bolt. At the same time the joint will be modified. | 3,898 |
| Dec 2009 | Fuel may leakFault: It has been identified that the fuel rail beneath the vehicle that protects the fuel line may not be properly attached thereby exposing the fuel lines to possible damage. Fix: Recalled vehicle will have the security of the subject rail checked. It will be secured if this is seen to be necessary. | 1,727 |
| Nov 2009 | Seat belt may detachFault: Under certain side impact scenarios the side panel on the driver's seat may contact the quick fix seatbelt release button and the belt may detach. Fix: Recall affected vehicles to modify the side panel. | 1 |
| Sep 2009 | Engine may stallFault: It has been identified thatthe fuel pump electronic module may not operate as intended. This can result in failure of the fuel pump to start. Should this occur the vehicle may suffer a non start rough running or in the worst case the engine may stall without prior warning. Investigation has shown that it may be possible to drive the vehicle for up to 100 m before the fault manifests itself. Fix: Recalled vehicles will have the software within the central electronic module upgraded. | 254 |
| Jun 2009 | Engine cooling fan may failFault: It has been identified that due to a software issue with the engine cooling fan control module the air conditioning performance may be reduced and the engine coolant temperature may increase. This will result in warning messages being displayed. In extreme cases if the driver does not heed the warnings the engine may fail. Fix: Recalled vehicles will have the cooling fan control module replaced. | 4,006 |
| Feb 2009 | Towing eye may not be capable of being correctly fittedFault: It has been identified that the front bumper energy absorber may be partially covering the aperture through which the towing eye is fixed. Customers will discover that it is not possible to fit the towing eye following removal of the bumper towing eye cover. Fix: Recalled vehicles will have a section of the bumper energy absorbing material removed thus allowing full access to the towing eye aperture. | 91 |
Nothing matches that search on this page.
Vehicles affected is the number DVSA lists for each recall.
How to check a car for recalls
A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.
A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.
Frequently asked questions
How do I check if my XC60 has an outstanding recall?
Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.
How many recalls has the Volvo XC60 had?
DVSA's recalls data lists 53 safety recalls covering the Volvo XC60, the most recent dated 23 June 2025. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Does a recall mean a car is unreliable?
No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
What should I do if my car is affected by a recall?
Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.
Where does this recall data come from?
From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.
Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.
Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.
Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.
Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.
What it can do
- ✓Free vehicle check: send any UK reg for the make, model, MOT and tax status
- ✓Send a photo of a number plate and we read the reg for you, then ask you to confirm it
- ✓Outstanding safety recall check, included in every lookup
- ✓Free valuation: add the mileage after the reg, for example 45k. A guide only, not an offer to buy or a guarantee of sale price See terms
- ✓Free MOT and tax reminders: reply REMIND with a reg (typos are fine)
- ✓Paid vehicle history check, with data provided by Experian, delivered in the chat
- ✓Find a vehicle: for example Ford Fiesta under 8k
- ✓Ask about a vehicle: send your question with the link to the vehicle on MotifyMe or its registration. Or search first, then reply ASK, the number of the vehicle and your question, for example ASK 2 is it still available. If we are not sure which vehicle you mean, we will ask
- ✓Fuel: live prices, plus a journey fuel cost such as London to Edinburgh
- ✓Fuel price alerts by email: send FUEL ALERT with your town or postcode, fuel and email address
- ✓How many are left: send HOW MANY and a model no longer sold new, for example HOW MANY Saab 9-3
- ✓Recalls: send RECALLS and a make or model, for example RECALLS Ford Puma
- ✓MOT pass rates: send MOT RATE and a model, for example MOT RATE Ford Fiesta
- ✓Diesel driver? Send FUEL CARD for the Accelerate diesel fuel card, up to 5p a litre
- ✓Reply STOP at any time to opt out
Looking for a Volvo XC60?
See used Volvo XC60 cars listed on the MotifyMe® marketplace.
See XC60 cars for sale