Mercedes-Benz E Class Recalls
Safety recalls covering the Mercedes-Benz E Class in DVSA's recalls data, newest first.
Last updated 22 November 2026
Short answer:
DVSA's recalls data lists 140 safety recalls covering the Mercedes-Benz E Class, the most recent dated 21 September 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Check a registration for outstanding recalls, free
Every Mercedes-Benz E Class recall
Open a recall to see the fault, the fix and the build dates it covers.
| Date | Recall | Vehicles affected |
|---|---|---|
| Sep 2026 | Srpc2603 - drive shaft jointFault: Mercedes-Benz AG has determined that on certain 4MATIC E-Class (213 platform) S-Class Coupé (217 platform) S-Class (222 platform) E-Class Coupe/Convertible (238 platform) GLC (253 platform) and CLS (257 platform) vehicles increased wear of the universal joint on the drive shaft might occur. Fix: As a remedy Mercedes-Benz AG via its Mercedes-Benz service partners will check the drive shaft on the affected vehicles and replace it if necessary. | 3 |
| Jun 2026 | Coolant pump control softwareFault: Mercedes-Benz AG has determined that on certain GLE/GLS (167 platform) C-Class (205 platform) E-Class (213 platform) S-Class (223 platform) GLC (253 platform) and CLS (257 platform) vehicles with diesel engine the vacuum‑controlled coolant pump might exhibit a leakage between the vacuum system and the coolant circuit. Fix: As a remedy Mercedes-Benz AG via its Mercedes-Benz service partners will update the software of the coolant pump and replace the electrical switch valve on the affected vehicles. | 1 |
| Jan 2026 | Srpc2521 - routing of transmission wiring harnessFault: Mercedes-Benz AG has determined that on certain E-Class AMG (214 platform) vehicles with 4-wheel-drive the routing of the transmission wiring harness might not meet specifications. Fix: As a precautionary measure Mercedes-Benz AG via its Mercedes-Benz service partners will check the routing of the transmission wiring harness on the affected vehicles and rework it if necessary. | 5 |
| May 2025 | Srpc2504 - ground connection boltingFault: Mercedes-Benz AG has determined that on certain E-Class (214 platform) and GLC (254 platform) vehicles the bolts of certain 12V- and 48V- ground connections might not have been fastened with the specified torque. Fix: As a remedy Mercedes-Benz AG via its Mercedes-Benz service partners will check the bolting of the ground connections and perform according repairs if necessary. | 4 |
| Dec 2024 | Srpc2421 - welding of rear axle carrierFault: Mercedes-Benz AG has determined that on certain E-Class 214 platform and GLC 254 platform vehicles the welding of consoles to the rear axle carrier might not meet specifications. Fix: As a remedy a Mercedes-Benz service partner will replace the rear axle carrier of the affected vehicles. | 2 |
| Dec 2024 | Srpc2419 misfire detection m264Fault: The software of the engine control unit might not meet specifications regarding misfire detection. Fix: Mercedes-Benz AG via its Mercedes-Benz service partners will update the software of the engine control unit on the affected vehicles. | 1,831 |
| Nov 2024 | Srpc2414 - function cross traffic alertFault: The manufacturer has determined on affected vehicles the software of the MBUX multi media system might not meet specifications. In this case a permanent deactivation of certain functions of assistance systems might occur. Fix: Update the parking control unit settings | 71 |
| Nov 2024 | Srpc2417 - function cross traffic alertFault: The manufacturer has determined on affected vehicles the software of the MBUX multi media system might not meet specifications. In this case a permanent deactivation of certain functions of assistance systems might occur. Fix: Update the parking control unit settings | 23 |
| Oct 2024 | Srpc2409 - tightness of transmission wiring harness connectorFault: The manufacturer has determined on affected vehicles the electrical connector of the transmission wiring harness might not have been correctly remedied. Fix: Replace the two-part wiring harness including the connector a with a new one-part variant. | 1,699 |
| Oct 2024 | Srpc2412 - tightness of transmission wiring harness connectorFault: The manufacturer has determined on affected vehicles the electrical connector of the transmission wiring harness might not have been correctly remedied. Fix: Replace the two-part wiring harness including the connector a with a new one-part variant | 271 |
| Apr 2024 | Srpc2406 - routing of transmission wiring harnessFault: On affected vehicles the routing of the transmission wiring harness might not meet specifications. The distance of the wiring harness to the drive shaft might be too small causing it to chafe. Fix: Check the routing of the transmission wiring harness and rework it if necessary. | 1 |
| Mar 2024 | Srpc2401 - system protectionFault: On certain vehicles some 80A fuses installed might not meet requirements. Fix: Replace the respective main fuse boxes on the affected vehicles. | 43 |
| Mar 2024 | Srpc2400 - bolting of 48 volt ground connectionFault: On certain vehicles the 48V ground connection in the engine compartment might not be secured correctly. Fix: Check the bolting of the ground connection on the affected vehicles and perform the respective repairs if necessary. | 1 |
| Aug 2023 | On affected vehicles the fuel pump impeller might not meet specifications and may deform.Fault: On affected vehicles the fuel pump impeller might not meet specifications and may deform. Fix: Replace the fuel pump module. | 1,511 |
| Aug 2023 | On affected vehicles the coding of the exit warning system might not meet specifications.Fault: On affected vehicles the coding of the exit warning system might not meet specifications. Fix: Update the coding parameters of the multimode radar. | 34 |
| Aug 2023 | On affected vehicles the manufacturing of the wiring harness to the power electronics might not meet specifications.Fault: On affected vehicles the manufacturing of the wiring harness to the power electronics might not meet specifications. Fix: Check the wiring harness and repair if necessary. | 1,726 |
| Feb 2023 | On affected vehicles the aluminium bolts of the steering gear could corrode and break due to the intrusion of moisture.Fault: On affected vehicles the aluminium bolts of the steering gear could corrode and break due to the intrusion of moisture. Fix: Replace the steering gear mounting bolts on the affected vehicles with steel bolts. Should the bolts break or already be broken change the steering gear. | 102,502 |
| Feb 2023 | The bonding between the glass panel and the sliding roof frame might not meet specifications.Fault: On affected vehicles the bonding between the glass panel and the sliding roof frame might not meet specifications. In consequence a separation of the glass panel from the vehicle cannot be excluded. Fix: Check the glass panel and replace the sliding roof if necessary. | 3,267 |
| Nov 2022 | The attachment for the 12v battery in the luggage compartment may not withstand the loads in the event of an accidentFault: On certain E-Class vehicles the attachment for the 12V battery in the luggage compartment may not withstand the loads in the event of an accident. Fix: Install an additional fixation of the 12V battery on the affected vehicles. | 3,645 |
| Sep 2022 | The transmission wiring harness might not be routed according to specificationsFault: The transmission wiring harness might not be routed according to specifications. Fix: Fit additional bracket to optimise the wiring routing. Check the harness connections and rework if necessary. | 2,456 |
| Aug 2022 | The routing of the transmission wiring harness might not meet specificationsFault: The routing of the transmission wiring harness might not meet specifications. Fix: Check the transmission wiring harness routing on the affected vehicles and replace it if necessary. | 1,482 |
| Jun 2022 | The bonding of the right rear door window bar might not meet specificationsFault: The bonding of the right rear door window bar might not meet specifications. Fix: Check the fixation of the window bar on the affected vehicles and replace the side window if necessary | 52 |
| Jun 2022 | The bolting of the 48v ground connection of the electrical refrigerant compressor might be fastened with an insufficient torqueFault: The bolting of the 48V ground connection of the electrical refrigerant compressor might be fastened with an insufficient torque. Fix: Check the bolting of the ground connection on the affected vehicles and correct it if necessary. | 13 |
| May 2022 | Individual bolts or chain links of the camshaft timing chain might wearFault: Individual bolts or chain links of the camshaft timing chain might wear in case of a long term operation under specific driving conditions. Fix: Replace the camshaft timing chain on the affected vehicles | 1,428 |
| May 2022 | The hands-off detection might not detect when the driver's hands are away from the steering wheelFault: The hands-off detection might not detect when the driver's hands are away from the steering wheel. Fix: Update the coding of the hand detection system on the affected vehicles. | 846 |
| May 2022 | The software of the headlamps might not meet specifications.Fault: The software of the headlamps might not meet specifications. Fix: Replace the affected headlamp control units on the vehicles. | 9 |
| Mar 2022 | A particle in the fuel rail might lead to a leak between the fuel rail and the injectorFault: A particle in the fuel rail might lead to a leak between the fuel rail and the fuel injector.� Fix: Replace the fuel rail and fuel injectors on the affected vehicles.� | 52 |
| Mar 2022 | The locking mechanism for the electrical connector of the left acceleration crash sensor at the bending beam might not meet specificationsFault: On certain vehicles the locking mechanism for the electrical connector of the left acceleration crash sensor at the bending beam might not meet specifications. Fix: Check the crash sensor at the bending beam on the affected vehicles and rework if necessary. | 2 |
| Feb 2022 | The software of the engine control unit might not meet specificationsFault: On certain vehicles the software of the engine control unit might not meet specifications. Fix: Conduct an update the software of the engine control unit on the affected vehicles. | 102 |
| Jan 2022 | Coolant pump might have a leakage between the vacuum system and the coolant circuitFault: On certain vehicles with a Diesel engine the coolant pump which is controlled by vacuum might have a leakage between the vacuum system and the coolant circuit. Fix: Update the software of the coolant pump and replace the electrical switch valve on the affected vehicles. | 106,872 |
| Jan 2022 | The crankshaft might not meet specificationsFault: On certain vehicles with a 4-cylinder Diesel engine the crankshaft might not meet specifications. Fix: Replace the engine on the affected vehicles. | 23 |
| Jan 2022 | Mounting screws of front axle brake callipers might not meet specificationsFault: On vehicles with a fixed�caliper�brake system the mounting screws of the�calipers�on the front axle may not meet specifications. Fix: Replace the screws on the front brake�calipers�on the affected vehicles.� | 72 |
| Dec 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 7 |
| Dec 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 23 |
| Dec 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 6 |
| Dec 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 21 |
| Nov 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 100,780 |
| Nov 2021 | Takata airbag might not deploy as specifiedFault: Certain climatic conditions may cause a chemical change to the airbag propellants over time. Fix: Replace the driver and passenger airbags. | 56 |
| Nov 2021 | Takata airbag might not deploy as specifiedFault: Certain climatic conditions may cause a chemical change to the airbag propellants�over time.� Fix: Replace the driver and�passenger airbags.� | 85,613 |
| Sep 2021 | The belt tensioner arm may have been manufactured with borderline toleranceFault: The belt tensioner arm may have been manufactured with borderline tolerance. Fix: Replace the belt tensioner. Additionally check the v-ribbed belt on the affected vehicles and replace it if necessary. | 427 |
| Sep 2021 | The locking mechanism for the electrical connector of the side crash sensors might not meet specificationsFault: The locking mechanism for the electrical connector of the side crash sensors might not meet specifications. Fix: Check the side crash sensors in the doors on the affected vehicles and replace them if necessary. | 129 |
| Aug 2021 | The driver's air bag may have a chemical change to its propellant over timeFault: The driver's airbag may have a chemical change to its propellant over time. Fix: Replace the driver�s airbag. | 108,486 |
| Aug 2021 | The driver's air bag may have a chemical change to its propellant over timeFault: The driver's airbag may have a chemical change to its propellant over time. Fix: Replace the driver�s airbag | 61 |
| Jul 2021 | The fixation of the rear headrests might not meet specificationsFault: The fixation of the rear headrests might not meet specifications. Fix: Check the guide sleeves on the rear seats of the potentially affected vehicles and replace them if necessary. | 320 |
| Jun 2021 | The software and hardware of the parking control unit might not meet specificationsFault: The software and hardware of the parking control unit might not meet specifications. Fix: Replace the parking control unit on the affected vehicles. | 16 |
| May 2021 | The bonding between the glass panel and the sliding roof frame might not meet specificationsFault: The bonding between the glass panel and the sliding roof frame might not meet specifications. Fix: Check the glass panel bonding on the affected vehicles and replace the sliding roof if necessary. | 310 |
| May 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 217,942 |
| May 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 173,208 |
| May 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 181,432 |
| May 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 162,534 |
| May 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 325,162 |
| May 2021 | The emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 12 |
| May 2021 | The emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 213,330 |
| May 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system. | 20,820 |
| May 2021 | The screw connection of the power supply on the starter might not have been installed according to specificationsFault: The screw connection of the power supply on the starter motor might not have been installed according to specifications. Fix: Check the screw connections of the starter motor and the position of the plus wire on the affected vehicles and correct them if necessary. | 70 |
| Apr 2021 | The two grab handles on the left side of the headliner may not be attached according to specificationsFault: The two grab handles on the left side of the headliner might not be attached according to specifications. Fix: Inspect the mounting of the grab handles on the left side of the affected vehicles and correct it if necessary. | 4 |
| Mar 2021 | The software of certain communication modules may not meet specificationsFault: The software of certain communication modules may not meet specifications. Fix: Carry out an update to the software of the communication module on affected vehicles. | 36 |
| Mar 2021 | The communication module may be deactivatedFault: The communication module may be deactivated Fix: Carry out a check of the configuration of the communication module on affected vehicles and if necessary activate the communication module. | 24 |
| Dec 2020 | The high voltage wiring harness shield may not permanently withstand the electrical loads that are induced under certain driving profilesFault: The shield for the high-voltage wiring harness may not permanently withstand the electrical loads that are induced under certain driving profiles Fix: Replace the high-voltage wiring harness on the affected vehicles | 2,377 |
| Nov 2020 | Software update required to improve emissionsFault: Certain specific calibrations of functions must be changed in the engine management of the vehicles Fix: Update the diesel engine control unit software and add a supplementary booklet for the operator�s manual. | 383 |
| Oct 2020 | The emergency call system (ECALL) does not meet the specificationFault: On affected vehicles the software of the communication module for the emergency call system does not meet the specification Fix: Update the software of the communication module for the emergency call system | 3,127 |
| Oct 2020 | The SEAT belt warning function does not meet the specificationFault: The seat belt warning function does not meet the specification Fix: Activate the correct seat belt warning scenario in the instrument cluster | 90 |
| Oct 2020 | Engine control unit software to be updatedFault: Improve the vehicle emissions via software updates. Fix: Update the relevant control unit�s software and if necessary replace the NOx sensors. | 994 |
| Oct 2020 | Certain specific calibrations of functions must be changed in the engine managementFault: Certain specific calibrations of functions must be changed in the engine management of the vehicles Fix: Update the diesel engine control unit software | 23,302 |
| Sep 2020 | Electro-chemical processes may create conductive connections inside the electric busbarFault: Electro-chemical processes might create conductive connections inside the electric busbar. Fix: Modify the busbar and install a separate electric line on the affected vehicles. | 11 |
| Aug 2020 | The data documenting the correct mounting of the turbocharger oil feed as well as the oil return line may be missingFault: The HV battery pack can overheat and result in the venting of hot gas which can ignite vehicle components or in extreme cases the entire vehicle. Fix: To prevent a vehicle fire the vehicles should not be charged using the external charging cable and the vehicles should only be driven using the default Auto EV mode only | 124 |
| Aug 2020 | The left rear SEAT backrest lock may not meet specificationsFault: The left rear seat backrest lock might not meet the specifications Fix: Replace the left rear seat backrest lock on the affected vehicles. | 1,179 |
| Aug 2020 | The elastomeric material of the oil feed line to the turbochargers may not meet specificationsFault: The material of the turbocharger oil feed pipe may not meet specification leading to leakage. Fix: Replace the oil feed pipe to the turbocharger on affected vehicles. | 434 |
| Aug 2020 | Certain front SEAT belt buckles may not have been manufactured according to specificationFault: A correctly fastened seat belt could be detected as not fastened impairing the restraint system Fix: Check the relevant seat belt buckles in the affected vehicles and replace if necessary | 15,652 |
| Jul 2020 | The seatbelt on the front left SEAT might not have been mounted according to specification.Fault: The seatbelt on the front left seat might not have been mounted according to specification Fix: Check the routing of the seatbelt on the front left seat on the affected vehicles and correct it if necessary. If the webbing is damaged the seatbelt will be replaced. | 2 |
| May 2020 | The bonding between the glass panel and the sliding roof frame may not meet specificationsFault: The bonding between the glass panel and the sliding roof frame might not meet specifications Fix: Check the glass panel bonding on the affected vehicles and replace the sliding roof if necessary | 18,132 |
| Oct 2019 | The spoiler on the rear door may have been mounted incorrectlyFault: The spoiler on the rear door might not have been mounted according to specification. Fix: Check the mounting of the rear door spoiler on the affected vehicles and rework it if necessary. | 11,130 |
| Oct 2019 | Software update required to improve emissionsFault: Improve the vehicle emissions via software updates. Fix: Update the diesel engine control unit software and add a supplementary booklet for the operator's manual. Check and replace NOx sensor if necessary. | 7,681 |
| Sep 2019 | The software of the radar control unit may not meet specificationFault: ; The software of the radar control unit might not meet the specification Fix: Update the software of the radar sensor control unit on the affected vehicles. | 294 |
| Sep 2019 | To achieve an improvement in the emissions via software updatesFault: Improve the vehicle emissions via software updates. Fix: Update the diesel engine control unit software and add a supplementary booklet for the operator's manual | 25,647 |
| Sep 2019 | The crankshaft may exhibit surface damagesFault: The durability of the crankshaft might be impaired. Fix: Replace the engine on affected vehicles. | 35 |
| May 2019 | An internal sensor within the electric power steering unit may not have been manufactured to specificationsFault: An internal sensor within the electric power steering unit might not have been manufactured according to specifications. Fix: The affected vehicles are to have the steering unit replaced. | 32 |
| May 2019 | Switches in certain SEAT belt buckles may not have been manufactured to specificationsFault: The switches in certain seat belt buckles might not have been manufactured according to specifications. Fix: The affected seat belt buckles are to be replaced. | 2,570 |
| Apr 2019 | A reset in the cpc control unit could occur whilst drivingFault: The ECO Start-Stop function may be disabled and cause the vehicle to stall. Fix: The affected vehicles are to be recalled and the software updated. | 69 |
| Apr 2019 | A lock nut may be cracked in the steering gearFault: A lock nut may be cracked in the steering gear. Fix: The electric power steering is to be checked and if necessary replaced. | 6,684 |
| Apr 2019 | The air conditioner housing may possibly not have been installed according to specificationFault: The airbag control unit may be damaged. Fix: Replace the air bag control unit on affected vehicles. | 5,159 |
| Apr 2019 | Right spoiler on rear door might not have been mounted according to specificationFault: The right spoiler on the rear door might not have been mounted according to specification. Fix: The right side spoiler is to be checked and replaced if necessary. | 202 |
| Apr 2019 | A lock nut may be cracked in the steering gearFault: A lock nut may be cracked in the steering gear. Fix: The electric power steering is to be checked and if necessary replaced. | 24 |
| Feb 2019 | Rear spoiler on rear end door may not have been fitted to specificationFault: The rear spoiler could detach from the vehicle completely. Fix: The security of the rear spoiler is checked and made safe if necessary. | 9 |
| Jan 2019 | The lock status of the steering coupling was not correctly documentedFault: The lock status of the steering coupling was not correctly documented following assembly. Fix: As a precautionary measure on affected vehicles the lock status of the steering coupling will be determined and reworked if necessary. | 4 |
| Jan 2019 | The routing of the fuel feed hose might not meet specificationsFault: Fuel hose might be incorrectly routed with a possibility of chaffing and leakage. Fix: Check the routing of the fuel feed hose on affected vehicles and rework it if necessary. | 31,658 |
| Dec 2018 | Front passenger SEAT occupant classification system calibration may not correspond to the specificationsFault: Incorrect calibration of the front passenger occupant classification system. Fix: Replace the seat cushion of the front passenger seat. | 151 |
| Nov 2018 | Faulty routing of sensor hose in front bumper may impair the function of the active hoodFault: The function of the active hood may be impaired. Fix: Check the routing of the silicone hose for the active hood and correct if necessary. | 152 |
| Oct 2018 | Child SEAT ISOFIX mounting support may be incorrect specificationFault: ISOFIX mounting support incorrect specification Fix: Replace ISOFIX mounting support on affected vehicles | 16 |
| Aug 2018 | Fault in navigation softwareFault: There is a fault in the navigation software on certain E-Class (213) Cars that have SD card navigation. Fix: Update the software of the navigation system on affected vehicles. | 6 |
| Aug 2018 | Incorrect underfloor panelling installedFault: Incorrect engine undertray fitted. Fix: Check and replace engine undertray on affected vehicles. | 15 |
| Aug 2018 | Driver's airbag gas generator housing failure during deploymentFault: On affected vehicles it has been determined that drivers airbags with potentially faulty gas generator housing material may have been installed in vehicles of model series 156 176 246 205 238 & 253. If the material of the gas generator housing fails during airbag deployment in the event of a crash the airbag system would possibly no longer have a restraint effect. In addition separating parts could enter the passenger compartment. This could lead to an increased risk of injury. Fix: On affected vehicles replace the driver�s airbag | 421 |
| Aug 2018 | Laser welding between backrest rail and backrest metal fitting of front seats may not meet specificationFault: It has been determined that on certain C-Class (205) and E-Class (213) Cars with AMG performance seats the laser welding between the backrest rail and the backrest metal fitting of the driver or passenger seat might not meet the specification. The laser welding between the backrest member and the backrest metal fitting may not withstand the required load values. As a result the fitting may detach from the backrest member. In the case of an accident this could result in a higher occupant load. Due to the delivery scenario the fault can only occur on one side of the seat. Fix: As a precautionary measure recall the affected vehicles and check the backrest member and replace if necessary | 46 |
| Jul 2018 | Right side of front SEAT backrests may not lock into placeFault: The seat backrests on the right side of the front seats in the c-class Coupe/Convertible and E-Class Coupe/Convertible may not fully lock. Fix: As a precautionary measure the lock of the seat backrest on affected vehicles will be check for operation. Where necessary the backrest will be replaced. | 21,366 |
| Jul 2018 | Electrical wiring in steering assembly may be insufficiently groundedFault: The steering column clock spring may break. This will cause warning messages to illuminate in the instrument cluster but in extreme instances it may cause the driver's airbag to deploy Fix: .Affected vehicles will be recalled to be checked to ensure there is sufficient grounding of the steering components. | 10,113 |
| Feb 2018 | Catalytic converter support bracket may be insecureFault: The screws retaining the catalytic converter bracket on the engine bracket may have an incorrect clench. This could lead to vibration and cause the exhaust to crack. Fix: On affected vehicles check screws according to manufacturer's procedures..Depending on findings either replace screws or refer to manufacturer for further guidance | 3 |
| Feb 2018 | Front SEAT belt tensioners may not functionFault: The front seatbelt pre-tensioner ignitors may not perform as expected. This could increase the risk of injury to the seat occupants. The lock function of the seatbelts is not impaired. Fix: On affected vehicles replace seatbelts with quality assured units. | 296 |
| Feb 2018 | Electrical wiring in steering assembly may be insufficiently groundedFault: The steering column clock spring may break. This will cause warning messages to illuminate in the instrument cluster but in extreme instances it may cause the driver's airbag to deploy. Fix: Affected vehicles will be recalled to establish sufficient grounding of the steering components. | 84,879 |
| Jan 2018 | Seatbelt pretensioner may not operateFault: Due to a deviation in the suppliers production process a specific squib batch may not comply with specifications In the event of an accident during which the left or right hand seat belt tensioner in the rear is activated with out squib ignition the belt may not fully restrain the occupant. Fix: On affected vehicles replace the left and right hand rear seat belts with a correct version. | 2,599 |
| Nov 2017 | Seatbelt pretensioner may not operateFault: Due to a deviation in the suppliers production process a specific squib batch may not comply with specifications In the event of an accident during which the left hand seat belt tensioner in the rear is activated the belt may not fully retrain the occupant. Fix: On affected vehicles replace the left rear seat belt with a correct version. | 796 |
| Oct 2017 | Right front SEAT belt pre-tensioner may not meet specificationFault: The right front seat belt pretensioner may not conform to specification . This may adversely affect it's operation in the event of an accident. Fix: Replace the pretensioner on affected vehicles. | 135 |
| Oct 2017 | Rear SEAT belt pre-tensioners may fail to restrain occupants as intendedFault: The rear seatbelt pre-tensioner ignitors may not perform as expected. This could increase the risk of injury to the seat occupants. The lock functions of the rear seatbelts are not impaired. Fix: Recall the 3400 vehicles that are likely to be affected and replace any potentially affected seatbelts with quality assured units. | 3,400 |
| Sep 2017 | Left front SEAT belt pre-tensioner may not meet specificationFault: The propellant mix in certain seatbelt pre-tensioners ignitors may be incorrect. If the front seatbelt pre-tensioners are deployed the lock function of the pre-tensioners cannot be guaranteed. Fix: Recall the vehicles that are likely to be affected and replace the front seatbelts that are likely to be affected. | 78 |
| Aug 2017 | Steering power assist may deactivateFault: The connector on the electric power steering control unit may not be properly sealed against water entry. If water enters the control unit the power steering assistance can be lost. The steering assistance not working could increase the risk of collision. Fix: Recall the vehicles that are likely to be affected and replace the plug housing of the electric power steering. | 5,121 |
| Jul 2017 | Oil leak from turbocharger feed pipe.Fault: Under certain conditions the oil feed pipe to the turbocharger may leak.Oil may contact hot components and there is a risk of fire. Fix: On affected vehicles replace the oil feed line to the turbocharger. | 73 |
| Jun 2017 | Airbag may not deploy correctlyFault: The propellant mixing ratio in the igniters of the front passenger airbag assembly may not meet specification. If the airbag is required and activated it might not deploy or not completely deploy. This could increase the risk of injury to the occupants. Fix: Recall the vehicles that are likely to be affected and replace the front passenger airbag assembly. | 1,034 |
| Jun 2017 | Starting current limiter may overloadFault: Where the car incurs severe engine damage resulting in the engine failing to turn over (engine seizure) and if the driver repeatedly attempts to start the engine despite the engine not cranking the very high electrical current could lead to overheating of the starting current limiter and the potential for a fire. Fix: Recall the vehicles that are likely to be affected and install an additional fuse in the electrical line to the starter. | 74,444 |
| Jun 2017 | Electric power steering motor defectiveFault: Contacts inside the electric power steering motor may not have been correctly formed. Failure of these contacts would cause the loss of power steering assistance.If this happens a warning lamp will illuminate Fix: Replace the electric power steering motor on affected vehicles. | 16 |
| Apr 2017 | Faulty control unit may cause vehicle to perform outside specificationFault: Where a control unit coding was updated in a workshop between 3 December 2016 and 5 December 2016 the coding may not correspond to the specification and may trigger unplanned action in the vehicle. The safety and emissions systems may not react as design intent. Fix: Recall the vehicles that are likely to be affected and update the software in the corresponding control units. | 42 |
| Mar 2017 | Steering column switch module may become inoperativeFault: It has been identified that the lever used to select the drive range on the steering column switch module may become inoperative due to possible damage of a circuit board. In the event of this fault occurs then manual selection of the drive range (D R N P) would no longer be possible. The Auto-P function as well as the automatic parking brake will still be available as intended. During manoeuvring the vehicle may not change the drive range as intended by the driver when operating the selector lever during standstill. This could result in an increased risk of a collision/accident. Fix: Recall all affected vehicles to replace the steering column switch module. | 3 |
| Mar 2017 | Short circuit may occurFault: The wiring to the front windscreen washers may not have been correctly routed. This may cause a short circuit and render the wipers in operative. Fix: On affected vehicles check wiring and rework where necessary. | 12,633 |
| Mar 2017 | Front airbag may be deactivatedFault: It has been identified that the front passenger seat occupancy weight sensing system control unit may have bee incorrectly installed during assembly. If the passenger seat is placed in the rear/lower position range then it can cause the pressure hose to become kinked which will reclassify the occupant as being a child seat. This will result in the front passenger airbag being deactivated and place the occupant at a higher risk of injury if the vehicle is involved in a frontal collision. Fix: Recall all affected vehicles to inspect the pressure pipe. If found to be kinked then the dealer is to contact MB Technical Department to establish the rectification process. | 7,494 |
| Feb 2017 | Loss of power steering supportFault: It has been identified that the pins within the electric power assisted steering control unit may not have been contact welded correctly. This can result in an open circuit which will lead to a loss of power steering assistance and possible loss of control of the vehicle. Fix: Recall all affected vehicles and replace electric power assisted steering. | 28 |
| Dec 2016 | Risk of fireFault: On certain 6 and 8 cylinder engine vehicles a faulty rear engine compartment panel/bulkhead may have been installed. It is therefore possible that the panel/bulkhead may contact the left exhaust catalytic converter due to insufficient clearance. If the catalytic converter is subjected to high temperatures due to heavy driving conditions i.e. full throttle or towing then there is a risk of the rear engine compartment panel igniting and a vehicle fire ensuing. Fix: Recall all affected vehicles to inspect the clearance between the rear engine compartment panel/bulkhead and the exhaust catalytic converter. If the clearance is insufficient then the rear engine compartment panel/bulkhead will be replaced. | 26 |
| Nov 2016 | Vehicle may cut outFault: The rear bench seat frame may impede the wiring harness connecting the fuel supply pump. This could affect fuel supply and the engine may cut out. Fix: On affected vehicles check condition of the wiring harness repair if necessary and reroute. | 4,231 |
| Jun 2016 | Engine may lose powerFault: The subject vehicle could unexpectedly lose drive and coast to a halt with no motive power due to a software issue in the powertrain control unit. In certain circumstances it is possible that the risk of collision is heightened. Fix: Recall the vehicles that are likely to be affected and update the software of the power train control unit. | 3,330 |
| Jan 2016 | Risk of fireFault: The high pressure fuel lines have not been manufactured to the correct specification which over time can lead to crack formation and fuel leaking. Fuel escaping in the presence of an ignition source could lead to fire. Fix: Recall the vehicles that are likely to be affected and replace the high pressure fuel lines. | 1,327 |
| Dec 2015 | Engine hood may not behave as intended in a collisionFault: The reset mechanism for the dynamic bonnet (for pedestrian protection) might not have been fitted during manufacture. In the event of a head on collision where the dynamic bonnet is triggered the bonnet may not behave as designed thereby putting the vehicle occupants at higher risk of injury. Fix: Recall the vehicles that are likely to be affected and check if the bonnet reset mechanism is fitted. Where the reset mechanism is missing fit a reset mechanism. | 1,111 |
| Nov 2015 | Engine may failFault: The camshaft could break and damage the engine due to it not being manufactured to the correct specification. If the condition occurs it will lead to a sudden loss of drive thereby increasing the risk of a collision. Fix: Recall the vehicles that are likely to be affected and replace the exhaust camshaft. | 395 |
| Aug 2015 | Fire may occurFault: The engine compartment seal may not be fully secure. There is a possibility that the seal may become dislodged and fall between the engine and the fire wall. If this occurs it is possible for the seal to contact very hot items such as the catalytic converter and a fire to start. Fix: Recall the vehicles that are likely to be affected and fit a new seal with fittings. | 3 |
| Jul 2015 | Front seats may not be secured acording to specificationFault: The threaded connections to the rear of the front seats may not have been tightened correctly. In the case of a serious vehicle accident the seat connection may not function as designed resulting in an elevated risk of injury to the occupants. Fix: Recall the vehicles that are likely to be affected to check and where necessary correct the torque of the connections at the rear of the front seats. | 10 |
| Mar 2015 | Fire may occurFault: A seal between bonnet and engine compartment may when the bonnet is opened temporarily stick to the bonnet. If this happens the seal may detach form its fixing and can fall into the gap between engine and partition wall. It is then possible the seal can make contact with the exhaust and under certain conditions catch fire. Fix: On affected vehicles install additional clips to retain the seal. | 3,863 |
| Jan 2015 | Oil may leakFault: On certain diesel engines the 'O' ring may not have been produced to the correct specification. This may allow oil to leak and contaminate the environment. If excessive oil is lost engine damage may occur. Fix: On affected vehicles replace the chain tensioner sealing ring. | 61,672 |
| Mar 2013 | Fuel may leakFault: The flange of the fuel filter may leak due to a non-compliance in the supplier's production process. Should this occur a fuel odour may arise or fuel escape. Fix: Recall the vehicles that are likely to be affected to replace the fuel filter. | 806 |
| Jan 2013 | Engine may cut outFault: Cracks in the charge air hose may possibly occur. This may subsequently lead to the engine switching to limp-home mode. In rare individual cases the engine shutting off cannot be ruled out. Fix: Recall the vehicles that are likely to be affected to replace the charge air hose. | 6,090 |
| Jan 2013 | Airbag may not deploy correctlyFault: During production monitoring Daimler AG became aware that in isolated cases on the E-Class coupe the air of the right windowbag may be able to escape more quickly than intended in the event that this is activated in an accident. In the event of a collision and in extreme cases the strict internal safety requirements of Daimler AG may not be adhered to. Fix: Replace the right windowbag as a precautionary measure. | 604 |
| Nov 2012 | Rear-axle suspension level sensor may breakFault: On E Class vehicles without AIRMATIC blocking of the level sensor linkage may occur. In extreme cases this may lead to breakage of the level sensor linkage. The linkage is used to measure the vehicle level via a sensor. If the linkage breaks it is possible the level sensor constantly records a vehicle level that is too low. This leads to a contact pressure rise in both air spring bellows and to hardening of the rear-axle suspension causing a noticeable loss in comfort. Fix: Replace the level sensor linkage on these vehicles as a precautionary measure. | 6,650 |
| Jan 2012 | Fuel may leakFault: Fuel leaks in the plug area of the drain opening may occur at the fuel filter with integrated fuel heaters. Fuel can escape and is noticeable to the customer due to a corresponding diesel odour. The diesel can reach the road and as a result friction between the tyres and road surface may be decreased. Fix: Check filter and replace as necessary. | 22,298 |
| Oct 2011 | Steering may become heavyFault: Power steering assistance may be lost due to an implausible signal occurring in the control unit. The mechanical steering of the vehicle is maintained but greater input from the driver will be required. When the fault occurs warning will be delivered both visually on the vehicle display and audibly via a signal tone. Fix: Recall the vehicles that are likely to be affected to replace the electric power steering units. | 316 |
| Jan 2011 | Fuel may leakFault: Fuel may leak from the fuel filter housing onto the road surface and thereby make the road slippery for road users. Fix: Recall the vehicles that are likely to be affected to replace the fuel filter housing if it is leaking. | 2,972 |
| Oct 2010 | Power assisted steering may leak oil.Fault: It is possible that a power assisted steering fluid leak could occur on the connection from the connection on the fluid line to pump. Drivers should be made aware of the concern by noise being emitted whilst the vehicle is being driven. Fix: Recall all affected to check the connection and if required replace the sealing ring. | 22,586 |
| Nov 2008 | Engine could lose power.Fault: The electrical connection in the interior of the crankshaft sensor's chip housing may be interrupted which may result in loss of power and the inability to restart engine Fix: Recall affected vehicles and replace crankshaft sensor | 19,331 |
| Nov 2008 | Engine emergency shut off on board diagnosis or tank/speedo signal may be affectedFault: Possibility of transfer of incorrect control unit software which could affect engine shut off control in an emergency situation or the on board diagnosis system or tank/speedometer signal Fix: Recall affected vehicles and replace SAM control unit | 72 |
| Jan 2006 | Engine may revert to limp home modeFault: The differential pressure sensor for the diesel particulate filter can fail due to contamination of the protective gel layer by exhaust gases. This will result in the car reverting to limp home mode (restricted engine speed). Fix: Replace the differential pressure sensor with the latest modified type. | 4,869 |
| Jul 2005 | Brake pedal may require more effort than expectedFault: In isolated cases it is possible for vibrations within the vehicle to in turn vibrate the wiring harness connected to the Sensotronic Brake Control unit. This causes the internal contacts within the unit to suffer abrasion and subsequent resistance increase. The resultant affect is that more effort will be required on the brake pedal to stop the vehicle. Fix: Recall the vehicles that are likely to be affected and mount an additional bracket to the electrical harness to prevent relative movement. | 58,022 |
| Jul 2005 | Brake pedal may require more effort than expectedFault: Problems may occur with the Sensotronic Brake Control (SBC) hydraulic unit that could affect the input required by the driver to stop the vehicle. Fix: Recall the vehicles that are likely to be affected so the SBC hydraulic unit can be checked and if necessary replaced. | 4,700 |
| Jul 2004 | Possibility of reduced braking efficiencyFault: Premature wear of the Sensatronic Brake Control (SBC) unit may lead to a reduced braking efficiency Fix: Recall affected vehicles download the latest software. Following the download the system will advise when the SBC hydraulic unit requires replacement. | 39,742 |
| May 2001 | Unintentional deployment of air bagFault: Exposure to high humidity conditions may result in corrosion that can cause the drivers front air bag to deploy unintentionally. Fix: Recall affected vehicles and replace air bag. | 7,041 |
| Oct 2000 | Potential loss of pas oilFault: Insufficient tightening of the power assisted steering damper screw may result in oil leakage. This oil may in extreme circumstances contact the exhaust system with the risk of an under bonnet fire. Fix: Recall affected vehicles and check the torque of the steering damper fastening screw. Replace the damper O ring seals if they are leaking. | 15,047 |
| Mar 2000 | Heater booster concernFault: Electrical heater booster may fail to switch off after the vehicle has been parked. This in extreme cases may lead to an under bonnet fire. Fix: Recall affected vehicles and install a relay and temperature controlled cut out to control the electrical heater booster. | 1,921 |
Nothing matches that search on this page.
Vehicles affected is the number DVSA lists for each recall.
How to check a car for recalls
A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.
A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.
Frequently asked questions
How do I check if my E Class has an outstanding recall?
Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.
How many recalls has the Mercedes-Benz E Class had?
DVSA's recalls data lists 140 safety recalls covering the Mercedes-Benz E Class, the most recent dated 21 September 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Does a recall mean a car is unreliable?
No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
What should I do if my car is affected by a recall?
Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.
Where does this recall data come from?
From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.
Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.
Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.
Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.
Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.
What it can do
- ✓Free vehicle check: send any UK reg for the make, model, MOT and tax status, plus any outstanding safety recall
- ✓Snap a number plate: send a photo and we read the reg for you, then ask you to confirm it
- ✓Free valuation: add the mileage after the reg, for example AB12 CDE 45k. A guide only, not an offer to buy or a guarantee of sale price See terms
- ✓Paid vehicle history check, with data provided by Experian, delivered in the chat
- ✓Free MOT and tax reminders: reply REMIND with a reg (typos are fine)
- ✓Recalls: send RECALLS and a make or model, for example RECALLS Ford Puma
- ✓MOT pass rates: send MOT RATE and a model, for example MOT RATE Ford Fiesta
- ✓How many are left: send HOW MANY and a model no longer sold new, for example HOW MANY Saab 9-3
- ✓Find a vehicle: tell us what you want, for example Ford Fiesta under 8k
- ✓Ask about a vehicle: send its MotifyMe link or reg with your question, or after a search reply ASK, the number and your question, for example ASK 2 is it still available
- ✓Fuel prices: live prices, plus a journey fuel cost such as London to Edinburgh
- ✓Fuel price alerts by email: send FUEL ALERT with your town or postcode, fuel and email address
- ✓Diesel driver? Send FUEL CARD for the Accelerate diesel fuel card, up to 5p a litre
- ✓Reply STOP at any time to opt out
Looking for a Mercedes-Benz E Class?
See used Mercedes-Benz E Class cars listed on the MotifyMe® marketplace.
See E Class cars for sale