Mercedes-Benz Sprinter Recalls
Safety recalls covering the Mercedes-Benz Sprinter in DVSA's recalls data, newest first.
Last updated 22 November 2026
Short answer:
DVSA's recalls data lists 124 safety recalls covering the Mercedes-Benz Sprinter, the most recent dated 19 December 2025. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Check a registration for outstanding recalls, free
Every Mercedes-Benz Sprinter recall
Open a recall to see the fault, the fix and the build dates it covers.
| Date | Recall | Vehicles affected |
|---|---|---|
| Dec 2025 | Weld seam on rear axle brake mounting flangeFault: Mercedes-Benz AG has determined that on certain Sprinter 907 model vehicles with a gross vehicle weight of 5.0 tons a brake connection flange might not have been properly welded to the support tube of the rear axle. Fix: As a remedy Mercedes-Benz AG via its Mercedes-Benz service partners will replace the rear axle on the affected vehicles. | 2 |
| Jan 2025 | Propeller shaft weld seamFault: On certain Sprinter model 907 vehicles a welding seam of the propeller shaft might not meet specifications. Fix: Replace the propeller shaft on the affected vehicles. | 2 |
| Aug 2024 | Replace spring u-bolts of rear axle springsFault: On affected vehicles the spring U-bolts may not have been subject to treatment to increase their hardness which may lead to them fracturing. Fix: Replace the spring U-bolts on the affected vehicles. | 1 |
| May 2024 | B-pillar reinforcementFault: On affected vehicles the weld points of a reinforcement in the right B-pillar may not correspond to the specifications. In this case the reinforcement in the B-pillar may work loose over time and fail to transmit the belt forces to the B-pillar as intended. This would increase the risk of injury in the event of an accident. Fix: Rework the B-Pillar on the affected vehicles if necessary. | 701 |
| Dec 2023 | On affected vehicles the fuel filter heater may be deactivated. if this happens a fuel gelling may occur at low temperatures and an unexpected loss of propulsion cannot be ruled out.Fault: On affected vehicles the fuel filter heater may be deactivated. If this happens a fuel gelling may occur at low temperatures and an unexpected loss of propulsion cannot be ruled out. Fix: Code the CDI control unit to ensure the activation of the fuel filter heater | 18 |
| Oct 2023 | On affected vehicles the wheel rim structure might not meet specifications. micro cracks might form in the rim structure.Fault: On affected vehicles the wheel rim structure might not meet specifications. Micro cracks might form in the rim structure. Fix: Change the wheel rims. | 1 |
| Sep 2023 | On affected vehicles the screw connection of the partition wall might not meet specifications.Fault: On affected vehicles the screw connection of the partition wall might not meet specifications. Fix: Check and rework the screw connections | 4 |
| Jul 2023 | On affected vehicles the fuse layout of the interior blower might not meet the requirements for permanent operation under the highest blower level.Fault: On affected vehicles the fuse layout of the interior blower might not meet the requirements for permanent operation under the highest blower level. Fix: Replace the fuse and its supply line and relocate the fuse. | 88,056 |
| May 2023 | Mercedes-benz ag has determined that on certain Sprinter 907 910 model vehicles the software of the instrument cluster control unit does not correspond with the latest series production configurationFault: On affected vehicles the instrument cluster may fail when starting.� Displays such as the speedometer fuel level indicator lamps and warning messages as well as the warning tones would not function. Fix: Update the instrument cluster software. | 6,184 |
| Apr 2023 | On certain vehicles an external ingress of fluids into the glow plug output stage may occur under specific conditions potentially resulting in an electrical short circuit and overheating of the component.Fault: On certain vehicles an external ingress of fluids into the glow plug output stage may occur under specific conditions potentially resulting in an electrical short circuit and�overheating of the component.� Fix: Replace the glow plug relay and install an additional glow plug relay cover on the affected vehicles. | 28,124 |
| Feb 2023 | On affected vehicles a component of the park pawl system may suffer extraordinary wear due to a certain type of customer usage and negatively affect the ability to park the vehicle safely.Fault: On affected vehicles a component of the park pawl system may suffer extraordinary wear due to a certain type of customer usage and negatively affect the ability to park the vehicle safely. Fix: Update the software of various control units. | 6,966 |
| Feb 2023 | On affected vehicles a component of the park pawl system may suffer extraordinary wear due to a certain type of customer usage and negatively affect the ability to park the vehicle safely.Fault: On affected vehicles a component of the park pawl system may suffer extraordinary wear due to a certain type of customer usage and negatively affect the ability to park the vehicle safely. Fix: Update the software of various control units. | 5,993 |
| Feb 2023 | On affected vehicles certain climatic conditions could over time lead to chemical alteration of the passenger airbag inflator propellant. in the event of a crash the inflator could rupture when the airbag is deployed.Fault: On affected vehicles certain climatic conditions could over time lead to chemical alteration of the passenger airbag inflator propellant.� In the event of a crash the inflator could rupture when the airbag is deployed.� Fix: Replace the passenger airbag | 12,926 |
| Nov 2022 | Specific climatic conditions may over time cause a chemical change in the propellant in the airbag inflator of certain takata airbags. in the event of an accident in which the airbag is deployed this change could cause the airbag inflator to burst due to increased internal pressure.Fault: Specific climatic conditions may over time cause a chemical change in the propellant in the airbag inflator of certain Takata airbags. In the event of an accident in which the airbag is deployed this change could cause the airbag inflator to burst due to increased internal pressure. Fix: Replace the affected front passenger airbags on the affected vehicles. | 53 |
| Oct 2022 | The driver airbag may not deploy correctly if activated.Fault: The driver airbag may not deploy correctly if activated. Fix: Replace the drivers air bag. | 102,548 |
| Sep 2022 | The driver airbag may not deploy correctly if activatedFault: The driver airbag may not deploy correctly if activated. Fix: Replace the drivers air bag. | 62,660 |
| Sep 2022 | The driver's front air bag may not deploy as intendedFault: The Drivers front air bag may not deploy as intended. Fix: Replace the drivers front airbag. | 234 |
| Jul 2022 | The driver's front air bag may not deploy as intendedFault: The Driver's front air bag may not deploy as intended. Fix: Replace the driver's front airbag. | 64,143 |
| Jul 2022 | The software of the rear-view camera on certain vehicles might not meet specificationsFault: The software of the rear-view camera on certain vehicles might not meet specifications. Fix: Update the software of the rear-view camera of the affected vehicles. | 8,184 |
| Jul 2022 | An incorrect diameter rear axle torsion bar (anti roll bar) might be installedFault: An incorrect diameter rear axle torsion bar (anti roll bar) might be installed. Fix: : Replace the rear axle torsion bar (anti roll bar) on the affected vehicles. | 16 |
| Apr 2022 | Crankshaft might not meet required specificationFault: On certain vehicles with an OM654 classic diesel engine the crankshaft might not correspond with the required specification Fix: As a precautionary measure the engines will be replaced on the affected vehicles | 3 |
| Apr 2022 | The wiring harness of the alternator may possibly have been swapped with the wiring harness of the electric steeringFault: The wiring harness of the alternator may have been swapped with the wiring harness of the electric steering in the assembly procedure of certain vehicles. Fix: Check the affected lines and if necessary connect the correspondent wiring harnesses. | 300 |
| Feb 2022 | A temporary fault with the automatic transmission internal park pawl mechanism may occurFault: On certain vehicles fitted with an automatic transmission (gearbox) on rare occasions a temporary fault with the automatic transmission internal park pawl mechanism may occur resulting in the park pawl not engaging as intended. Fix: As a precautionary measure the Mercedes-Benz service organisation will update the ESP control unit software with a revised parameter set on the affected vehicles. | 5,962 |
| Jan 2022 | The engagement hooks of the cable duct of the starter-generator wiring harnessmay not be fully latched in the battery caseFault: On certain vehicles the engagement hooks of the cable duct of the starter-generator wiring harness may not be fully latched in the battery case. Fix: Check the fixings of the cable bracket and replace the engagement hooks of the affected cable duct with expanding rivets if required. | 132 |
| Dec 2021 | The distance between the brake line and wiring harness may not be sufficientFault: On certain Mercedes-Benz Sprinter vehicles the distance between the brake line and the wiring harness may not be sufficient. Fix: Check and apply an anti-chafe protection to the affected components. If damage to the components is already evident then the affected components will be replaced and anti-chafe protection applied. | 12,696 |
| Dec 2021 | Cracks could form in the connecting section of the trailer-coupling block/crossmember over the vehicle lifeFault: On certain vehicles with a trailer coupling block with tow ball cracks could form in the connecting section of the trailer-coupling block/crossmember over the vehicle life. Fix: Replace the affected trailer-coupling block/crossmember with a reinforced variant. | 24 |
| Dec 2021 | The actual installation condition of the communication module and its correct commissioning cannot be traced due to an error in productionFault: On certain vehicles the actual installation condition of the communication module and its correct commissioning cannot be traced due to an error in production. Fix: Check the installation condition of the communication module and depending on the actual condition of installation either retrofit it or if it is already available put it into correct operation. | 24 |
| Dec 2021 | The behaviour of the emergency call system might not meet specificationsFault: On certain vehicles the behaviour of the emergency call system might not meet specifications. Fix: Update the software of the HERMES communication module for the emergency call system on the affected vehicles | 5,066 |
| Dec 2021 | None or not approved cable ties have been used for additional fastening of the main wiring harnessFault: On certain vehicles no or not approved cable ties have been used for additional fastening of the main wiring harness on the cable duct of the starter-generator wiring harness. Fix: Replace the existing cable tie and plug holder with the approved fastening elements or use the approved fastening elements in cases where cable ties have not been used yet. | 6 |
| Oct 2021 | Update the software in the engine control unitFault: Mandatory recall requiring the updating of software in the engine control unit with the Euro 5b+ N1 GR.III/N2 emissions standard. Fix: Update the software in multiple control units depending on vehicle specification and options.� | 10 |
| Oct 2021 | Changes to specific aspects of the engine control system calibration are requiredFault: Changes to specific aspects of the engine control system calibration are required. Fix: Depending on vehicle specification and options software updates to multiple control units will be conducted. | 66,177 |
| Sep 2021 | Electrical cables may be improperly routed or mounted within the front swivel SEAT framesFault: Electrical cables may be improperly routed or mounted within the front swivel-seat frames. Fix: Inspect the installation of the seat wiring harness (left/right) of the front seats and attach the mounting clips to the intended position. | 1 |
| Sep 2021 | The brake hose of the front axle could touch and chafe the wheel housing interior lining.Fault: The brake hose of the front axle could touch and chafe the wheel housing interior lining. Fix: Exchange the brake hoses on the front axle on the affected vehicles with a revised version. | 3,138 |
| Sep 2021 | The ESP software has not been customised for upfitted vehicles with a higher centre of gravityFault: Vehicles may have received a version of the ESP Software application that has not been customized for upfitted vehicles with a higher centre of gravity. Fix: Update the software version of the corresponded ESP control unit. | 1 |
| Aug 2021 | The hydraulic power steering return line hoses may detach at their connection pointsFault: The hydraulic power steering return line hoses may detach at their connection points under certain operating conditions and may cause hydraulic fluid to leak. Fix: Check the return line connections of the power steering and install a screw type clamp at the connection point if needed. | 5,621 |
| Aug 2021 | One or more of the rear wheel speed sensors may experience an electrical failureFault: One or more of the rear-wheel speed sensors may experience an electrical failure. Fix: Replace the rear-wheel speed sensors on affected vehicles | 55 |
| Jun 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system on the affected vehicles. | 27,214 |
| Jun 2021 | The behaviour of the emergency call system might not meet specificationsFault: The behaviour of the emergency call system might not meet specifications. Fix: Update the software of the communication module for the emergency call system on the affected vehicles. | 42,820 |
| May 2021 | The retaining washer on the bolt connecting the brake pedal to its bearing block could come looseFault: The retaining washer on the bolt connecting the brake pedal to its bearing block could come loose. Fix: Secure the bearing bracket on the brake pedal by means of an additional retaining ring on the affected vehicles. | 44,820 |
| Apr 2021 | The rescue cutting line located in the SEAT box of the driver SEAT may not be accessibleFault: The rescue cutting line located in the seat box of the driver seat may not be accessible. Fix: Reposition the rescue loop on affected vehicles. | 628 |
| Apr 2021 | An incorrect fuse type for the electric system of the air suspension could have been mounted by errorFault: The fuse for the electric system for the air suspension may be incorrectly specified. Fix: Check the currently installed fuse and control unit on the potentially affected vehicles and replace if necessary. Also replace the fuse assignment booklet if necessary. | 14 |
| Apr 2021 | The gear recognition function in the transmission could not function as intendedFault: The reverse gear light may occasionally be non-functional until the next ignition change or the next engine start. Fix: Update the software responsible for gear recognition on the affected vehicles. | 11,394 |
| Mar 2021 | The rear brake calliper may leak brake fluid into the housing of the electric parking brakeFault: The rear brake calliper may leak brake fluid into the housing of the electric parking brake. Fix: Replace the rear brake callipers and update the ESP software. | 8,826 |
| Mar 2021 | The accelerator pedal may not have been mounted on the vehicle in accordance with the specificationFault: The accelerator pedal may not have been mounted on the vehicle in accordance with the specification. Fix: Check the correct installation of the accelerator pedal on the affected vehicles and if necessary renew it. | 9 |
| Mar 2021 | A software update of the electronic stability programme (ESP) control unit is requiredFault: A software update of the Electronic Stability Programme (ESP) control unit is required. Fix: Update the ESP control unit software in the affected vehicles. | 153 |
| Feb 2021 | The electrical wiring harness pre-installation for the hermes control unit could become stuck between the brake light switch and the brake pedalFault: The electrical wiring harness pre-installation for the HERMES control unit (communication module) could become stuck between the brake light switch and the brake pedal Fix: Correct the routing of the concerned wiring harness through the installation of an additional cable tie. | 17 |
| Dec 2020 | On affected vehicles front and rear brake hoses may have sustained an outer cutFault: On affected vehicles front and rear brake hoses may have sustained an outer cut. Fix: Check brake hose condition and renew if necessary. | 1,564 |
| Dec 2020 | Possible damage and short circuit of the glow plug Relay in certain collision scenariosFault: Possible damage and short circuit of the glow plug relay in certain collision scenarios Fix: Retrofit a housing for the glow plug relay and install a pyrotechnic fuse on the affected vehicles | 9,372 |
| Dec 2020 | Vehicles were produced and delivered without the necessary rear underride guardFault: Vehicles were produced and delivered without the necessary rear underride guard. Fix: Retrofit the rear underride guard on the affected vehicles. | 37 |
| Sep 2020 | The electric lines routed near the frame for the rotating seats may get jammedFault: Electric lines routed near the frame for the rotating seats may get jammed and thus be damaged. Fix: Correct the routing of the wiring harnesses of the rotating seats on the affected vehicles. | 540 |
| Aug 2020 | Incorrectly implemented threaded connection of the propeller shaft intermediate bearings at the underbodyFault: The threaded connection of the propeller shaft intermediate bearings at the underbody has not been verifiably documented in certain Sprinter vehicles. Fix: Renew the screws of the propeller shaft intermediate bearing and tighten them with the specified torque in the affected vehicles. | 4 |
| Jun 2020 | The operating manual does not specify certain conditions under which the automatic parking function of the automatic gearbox operatesFault: The operating manual does not correctly specify certain conditions under which the automatic parking function (Auto-P) of the automatic gearbox operates. Fix: Add a supplementary booklet with a correct description of the Auto-P function to the operating manual. | 12,950 |
| May 2020 | The wheel arch liner on the front axle could touch and chafe the flexible brake hoseFault: The wheel arch liner on the front axle could touch and chafe the flexible brake hose. Fix: Check the condition and clearance of the flexible brake hoses replacing them if necessary. Additionally the corresponding wheel arch liner will be modified to provide adequate clearance. | 38,865 |
| Mar 2020 | A weld seam on the SEAT height adjustment mechanism may not be to specificationFault: A weld seam on the seat height adjustment mechanism may not have been carried out in accordance with specifications Fix: Replace the seat-frame bases of the front seats in the affected vehicles | 12 |
| Mar 2020 | The rear axle steel leaf springs may not meet all requirements for strength during operationFault: The rear axle steel leaf springs may not meet all requirements for strength during operation Fix: Check if the rear axle springs on the affected vehicles are a part of an affected production batch and replace them if necessary | 1,153 |
| Nov 2019 | Vehicles were delivered with a higher transmission oil level than intendedFault: Vehicles were delivered with a higher transmission oil level than intended. Fix: Check the transmission oil level and drain any excess transmission oil if necessary. | 23 |
| Nov 2019 | A thermal overload can occur at the fuse carrier of the compressor for the air suspension and associated linesFault: A thermal overload can occur at the fuse carrier of the compressor for the air suspension as well as at the associated lines. Fix: The fuse holder and fuses of the air suspension compressor will be removed and the electric lines will be checked and replaced if necessary. | 9 |
| Nov 2019 | The screw connection on the upper hood catch may not have been carried out correctlyFault: The screw connection of the upper hood (bonnet) catch may not have been secured properly Fix: Check the torque of the screw connection and replace any missing screws if necessary | 8,362 |
| Sep 2019 | If the rotary light is switched to a different position very quickly the brightness of the rear lamps may be reduced significantly.Fault: A malfunction of the rear lamps may occur Fix: The signal and actuation module will be re-coded on the affected vehicles | 6,467 |
| Jun 2019 | The high beam cannot be deactivated by using the high beam leverFault: Main beam not deactivating automatically with 'High-Beam Assist' Fix: Update the software for the signal acquisition and actuation module on the affected vehicles. | 88 |
| Jun 2019 | A centralising sleeve may not have been installed between the automatic transmision and the direct shift moduleFault: Automatic transmission Direct Shift Module fault. Vehicle may roll away or drive in a direction not intended. Fix: Replace the Direct Shift Module together with the centralising sleeve on affected vehicles. | 6 |
| Apr 2019 | Incorrect description of the vehicle jack support points on rear axle in digital owner's manualFault: The Digital Owner's Manual contains an incorrect description of the vehicle jack support points at the rear axle. Fix: Update the Digital Owner�s Manual by updating the head unit control unit software. | 43 |
| Apr 2019 | The cross bridge at the rear axle may not withstand internal durability specifications.Fault: The cross-bridge at the rear axle may not withstand the internal durability specifications. Fix: Inspect potentially affected cross-bridges and replace if a weld seam is missing. Install a cross-bridge reinforcement strut. | 2 |
| Apr 2019 | Vehicles may have been delivered without the printed version of the operator's manualFault: Vehicles may have been delivered without the printed version of the operator's manual. Fix: Supply the missing printed version of the operator�s manual and/or any missing supplements of the vehicle service folders. | 27 |
| Apr 2019 | Failure of the glow plug RelayFault: A failure of the glow plug relay may result in an electrical short circuit and in overheating of the component. Fix: Replace the glow plug relay and provide an additional protective relay shield on the vehicles affected. | 114,203 |
| Mar 2019 | The connection between the steering shaft and steering gear may have been fitted with an incorrect boltFault: The bolted connection between the steering shaft and steering gear may have been fitted with a bolt of the wrong length. Fix: Vehicles to be checked to confirm if the correct bolt is installed and replace it if this was not the case. | 7 |
| Feb 2019 | Incorrect door lock operating lever on right side of vehicle may have been installedFault: An incorrect operating lever might have been installed to the door locks on the right side of the vehicle. Fix: Door locks are to be checked and replaced if necessary. | 874 |
| Feb 2019 | Incorrect door lock operating lever on right side of vehicle may have been installedFault: An incorrect operating lever might have been installed to the door locks on the right side of the vehicle. Fix: Door locks are to be checked and replaced if necessary. | 365 |
| Dec 2018 | Post-collision brake function within ESP was not activated during productionFault: The post-collision brake function within the Electronic Stability Programme was not activated during production. Fix: The Electronic Stability Program control unit software will be updated to the latest version. | 298 |
| Dec 2018 | The blind spot monitoring exit warning sub feature does not function as designed after the ignition is switched offFault: Vehicle exit warning feature does not function as designed after the ignition is switched off. Fix: Update both front door control units software on the affected vehicles. | 8 |
| Dec 2018 | An incorrect length linkage was mounted on the rotation angle sensor of the rear axleFault: An incorrect length linkage fitted to headlight range control sensor. Fix: Replace headlamp range control level sensor. | 1 |
| Dec 2018 | Driver support and assist functions distronic hold drive away assist and rcta are not active or available in the ESP due to a software errorFault: Driver support and assistant functions are not active or available in the ESP control unit due to a software error. Fix: The software of the ESP control unit will be up-dated with the latest version. | 74 |
| Dec 2018 | Backlight illumination of the hazard warning push button switch is deactivated after approx 20 mins driving due to faulty softwareFault: The backlight illumination of the hazard warning push button switch is deactivated after approximately 20 minutes driving. Fix: Software in the control unit will be updated with the latest version. | 1,540 |
| Dec 2018 | Blind spot monitoring exit warning inoperable after ignition switched offFault: Blind spot vehicle exit warning failure Fix: Update software on affected vehicles | 31 |
| Aug 2018 | Spot welds may not have been correctly applied to door frameFault: Spot welds on the front side wall that join the door frame with the hinge reinforcements behind it might not have been applied Fix: On affected vehicles check spotwelds and apply if missing. | 667 |
| Jul 2018 | Front axle toe adjustment incorrectly calculatedFault: The toe adjustment for the front axle was incorrectly calculated and set during production. Fix: Measure the front axle adjustments (toe and camber) and correct them. | 19 |
| Jul 2018 | Gas fuel cylinders may failFault: Gas fuel tanks fitted to affected vehicles may be affected by corrosion. Over time corrosion may weaken the tank wall(s) and the tank may burst. Fix: On affected vehicles check gas fuel tanks for corrosion. assess and where necessary replace. | 18 |
| Dec 2017 | Windshield may not be installed correctlyFault: The windscreen may not be correctly sealed in the upper middle area which may allow water to enter the cabin area. Fix: On affected vehicles check installation of windscreen and if necessary re-install. | 128 |
| Nov 2017 | Vehicle control unit may not have been correctly updatedFault: The vehicles electronic control unit (ECU) may have been incorrectly updated. This may affect the operation of systems controlled by the ECU Fix: On affected vehicles update the software of the control unit | 4 |
| Aug 2017 | Rear spring SEAT bases may failFault: The rear spring seat bases may develop cracks. Therse could case the seat base(s) to fail and the spriing(s) may detach. Fix: On affected vehicles repalce the rear spring seat bases | 69 |
| Jan 2017 | Trailer hitch may detachFault: Two out of the four screws/bolts of the trailer hitch may not have been tightened correctly resulting in excessive stress to the other bolts. It is therefore possible that over time the connection could fail and the trailer detach from the towing vehicle increasing the risk of incident. Fix: Recall the vehicles that are likely to be affected and replace the fixing bolts/screws for the towing attachment. | 1 |
| Nov 2016 | Seat belt restraint may be impairedFault: The seatbelt mountings on the two seater bench seats may not be correctly tightened. This could cause the seatbelts not fully restrain the passengers and heighten the risk of injury if the vehicle is involved in a collision. Fix: Recall the vehicles that are likely to be affected and check the seatbelt mouintings. Retighten the seatbelt mountings to the correct torque. | 9 |
| Sep 2016 | Window adhesion may not be sufficiently bondedFault: In the event of an accident the windows bonded tie down rails and the super high roof (if fitted) could detach and increase the risk of injury due to the lack of adhesion of non-conforming paint. Fix: Recall the vehicles that are likely to be affected and remove/install all bonded windows (excluding the windshield) and tie down rails and/or super high roof (if present) as well as repainting the corresponding bonding surfaces. | 61 |
| Sep 2016 | Bonded windows may detach in a collisionFault: In the event of an accident the windows bonded tie down rails and the super high roof (if fitted) could detach and increase the risk of injury due to the lack of adhesion of non-conforming paint. Fix: Recall the vehicles that are likely to be affected and remove/install all bonded windows (excluding the windshield) and tie down rails and/or super high roof (if present) as well as repainting the corresponding bonding surfaces. | 5 |
| Apr 2016 | Windows may detachFault: On vehicles with multi layered paint it is possible the layers may not have bonded as intended. This could allow the windscreen to detach in the event of excessive forces such as an accident. This may similarly affect bonded tie downs and/or super high roof. Fix: Recall affected vehicles and check stability of the paint. Where necessary reapply paint to affected areas. | 28 |
| Feb 2016 | Risk of fireFault: On vehicles fitted with the four cylinder (OM651) engine the high pressure fuel lines may not have been manufactured to specifications. These lines may crack and allow fuel to leak. If an ignition source is present there is a risk of fire. Fix: On affected vehicles replace high pressure fuel lines. | 826 |
| Dec 2015 | Seatbelt mechanism may malfunctionFault: The threaded connections of the seatbelts at the B-Pillars were possibly not tightened with the required torque. If the required torque is not present it is possible the threaded connection may loosen further. In the event of a loosened threaded connection the intended restraint effect of the seat belt cannot be guaranteed in the event of a collision and the risk of injury during an event may possibly be increased. Fix: Recall the vehicles that are likely to be affected and check and where necessary tighten the threaded connection. | 45 |
| Jan 2015 | Oil may leakFault: On certain diesel engines the 'O' ring may not have been produced to the correct specification. This may allow oil to leak and contaminate the environment. If excessive oil is lost engine damage may occur. Fix: On affected vehicles replace the chain tensioner sealing ring. | 21,679 |
| Feb 2014 | Vehicle stability may be affectedFault: It has been established that on certain models of NCV3 (5-ton) vehicles fitted with air suspension from the VB AirSuspension company have a high risk of a fracturing of the weld seam on the rear axle spring saddle. In the unlikely event that this occurs then the rear axle can become loose and take on a self-steering behaviour which could affect vehicle control or stability. Fix: Recall all affected vehicles to fit an additional spring saddle clamp to provide additional security. | 246 |
| May 2012 | Incorrect cross-member bolts fittedFault: The screws/bolts used for fastening the towing eyes the cross-member of the trailer hitch and the rear step for the support of the cross-member on 5 ton vehicles may be the wrong type. This could cause the bolts to work loose and in a worst case snap. Fix: As a precautionary measure the screw/bolts will be replaced on affected vehicles. | 15 |
| Jan 2012 | Fuel may leakFault: A fuel leak may occur from the area of the fuel drain opening in the fuel filters which leaks onto the road. Fix: Recall the vehicles that are likely to be affected to check the fuel filter and replace where necessary. | 6,035 |
| Dec 2011 | Control may be lostFault: Rear suspension springs may not be to specification and could fail at the spring eye. If such a failure occurs vehicle control could be lost. Fix: Recall the vehicles that are likely to be affected to check and where necessary replace the suspension springs. | 9 |
| Aug 2011 | Misleading instrument cluster information and ESP functionsFault: A program error may result in misleading instrument cluster information and ESP functions Fix: Re-Program the control unit and conduct SCN coding of the SRS control unit. | 118 |
| Jun 2011 | Passenger SEAT may detachFault: Rivets retaining the seat cushion of the front passenger seat may be too small and in an accident may not retain the cushion. This could lead to an increased risk of injury. Fix: Recall the vehicles that are likely to be affected to replace the double front passenger bench seat. | 23 |
| Dec 2010 | Fuel may leakFault: It is possible that vehicles fitted with integral heaters within the fuel filter could suffer a leak in the upper plug area. This leakage should be identified to the driver by the smell of the diesel however if action is not taken to address the issue the issue could result in fuel escaping onto the road surface. Fix: Recall all affected vehicles and replace the fuel filter. | 753 |
| Oct 2010 | Oil may leakFault: Oil may leak from the bottom of the engine oil filler neck. If not rectified this could lead to oil leaking onto the road surface and/or engine damage due to insufficient lubrication. Fix: Recall the vehicles that are likely to be affected to replace the engine oil filler neck. | 148 |
| Aug 2010 | Incorrect headlamp fittedFault: It has been established that some vehicles may have been fitted with headlights that are dipping to the offside headlights not to the nearside. Fix: Recall affected vehicles and replace headlights. | 19 |
| Jul 2010 | Seat belt may not restrain passengerFault: The seat belt mounting bolts in the areas of the B pillar and seat base have been found not to specification. In the event of an accident the restraint function of the seat belt may not be guaranteed. Fix: Recall the vehicles that are likely to be affected to check and where necessary adjust the torque of the seat belt mounting bolts in question. | 72 |
| Mar 2010 | Fire may occurFault: It has been identified that the fleece filter insert of the engine oil separator may become obstructed with dirt particles. It is therefore possible that an increase in pressure within the crankcase may occur with the result that oil could escape onto hot engine parts. Should this occur a fire may ensue. Fix: Recalled vehicles will have the original oil filter replaced with one of a cyclone type. | 8,058 |
| Jan 2010 | Risk of fireFault: A incorrect cable duct retaining bolt has been fitted. In the event of a crash the cable duct may detach at least partially from the engine. In this situation it is more likely that a short circuit of the unfastened starter/alternator line may occur. Fix: Recall the vehicles that are likely to be affected to replace the mounting bolt and fix the starter wiring in place. | 47 |
| Jul 2009 | Fire may occurFault: It has been identified that due to a fault with the previous recall to perform an engine ECU flash upgrade engine damage could occur as a result of piston cracking. As a consequence and in the worst case oil may enter the engine compartment where it could come into contact with hot engine parts which may result in a fire. Fix: Recalled vehicles will have the subject ECU loaded with modified software. | 132 |
| May 2009 | Parking brake may failFault: It has been identified that on certain vehicles the threaded insert of the parking brake adjuster may break under load due to insufficient wall thickness. Should breakage of the adjuster occur parking brake efficiency will be lost. Fix: Recalled vehicle will have the parking brake adjuster replaced with a quality assured item. | 16 |
| Mar 2009 | Possible engine bay fire and parking brake failureFault: It has been identified that as a result of a cracked piston engine damage can occur whereby oil is ejected into the engine bay and may ignite after coming into contact with hot engine components. It has further been identified that the threaded portion of the brake adjuster for the parking brake may break under load due to the wall thickness being too slight. Should a failure occur the parking brake would become ineffective. Fix: Recalled vehicles will be fitted with modified engine control software and will also have the parking brake adjuster replaced with a quality assured item. | 95 |
| Mar 2009 | Possible engine bay fireFault: It has been identified that as a result of a cracked piston engine damage can occur whereby oil is ejected into the engine bay and may ignite after coming into contact with hot engine components. Fix: Recalled vehicles will be fitted with modified engine control software. | 1,537 |
| Nov 2008 | Side mounts of the roof bed ladder may failFault: It has been established that the side mountings for the roof bed ladder are insufficient to hold it in place. As a result the ladder could slip sideways. Fix: Recalled vehicles will have the roof bed ladder replaced. | 1 |
| Nov 2008 | Potential failure of rear axleFault: It has been identified that the rear axle left hand side half shaft may develop cracks. Should this occur breakage of the rear axle might ensue. Fix: Recalled vehicles will have the rear axle inspected and replaced if necessary. | 53 |
| Sep 2008 | Electronics may not be fully functionalFault: The full functionality of the vehicles electronics which includes the safety systems cannot be guaranteed. This is a result of incorrect software being transmitted to a number of vehicles. Fix: Recall the vehicles that are likely to be affected to re-perform the software (SCN) coding to the control unit. | 11 |
| Jun 2008 | Increased brake pedal travelFault: It has been identified that an incorrect brake master cylinder and or brake fluid reservoir has been installed. In instances of the installation of an incorrect brake master cylinder the brake pedal will travel further before the brakes become effective. On vehicles fitted with an incorrect brake fluid reservoir the brake wear limit light will illuminate prematurely. Fix: Recalled vehicles will have the brake master cylinder and or the brake fluid reservoir replaced. | 19 |
| Jun 2008 | Increased brake pedal travelFault: It has been identified that subject vehicles have been fitted with an incorrect brake master cylinder. This has the effect of the brake pedal having to travel further before the brakes take effect. Fix: Recalled vehicles will have the brake master cylinder replaced. | 217 |
| Jun 2008 | Ecu maximum road speed limit not setFault: The maximum road speed limit was not set in the engine control unit during production. Fix: Recall the vehicles that are likely to be affected to set the maximum road speed of the vehicle. | 5 |
| May 2008 | Risk of fireFault: It has been identified that the lens of the interior lamps located in the air ducts may not conform to specification under conditions of continuous operation. This may result in an electrical short circuit and an isolated cable fire. Fix: Recalled vehicles will have the subject lamps replaced. | 9 |
| Apr 2008 | Short circuit may occurFault: Fire may occur in vehicles fitted with rear air conditioning as a result of the rear interior lamp deforming because of its position in continuous heat.The deformation in combination with moisture may trigger a short circuit of the connecting contacts and thereby cause an isolated cable fire. Fix: Recall the vehicles that are likely to be affected to replace the interior lamps in the rear passenger compartment. | 9 |
| Oct 2007 | Airbag may not inflate correctlyFault: In the case of an incident where the air bags deploy as a result of the offside window bag module possibly having been fitted with a defective diffuser the air bag may not fully inflate and parts of the window bag module may detach and fly into the interior compartment at high speeds. Fix: Recall the vehicles that are likely to be affected to replace the offside window bag module. | 4 |
| Oct 2007 | Airbag may not deploy correctlyFault: In the case of an incident where the air bags deploy as a result of the offside window bag module possibly having been fitted with a defective diffuser the air bag may not fully inflate and parts of the window bag module may detach and fly into the interior compartment at high speeds. Fix: Recall the vehicles that are likely to be affected to replace the offside window bag module. | 1 |
| May 2007 | Vehicle may cut outFault: It has been identified that a possible poor contact with the fuel pump relay in the fuse and relay module unit may affect the operation of the fuel pump and cause the engine to cut out. Fix: Recall all affected vehicles to check the manufacturing date of the fuse and relay module unit and it necessary replace it. | 136 |
| Apr 2007 | Short circuit may occurFault: It is possible that an incorrect size terminal may have been fitted to the starter wiring harness. It could result in the wiring not being crimped correctly and cause a detachment of the wiring which could result in a short circuit. Fix: Recall all affected vehicles and replace the starter-alternator wiring harness. | 9 |
| Mar 2007 | Crash signal protocol may not occur in the event of a collisionFault: A software error may exist in the airbag control unit which can prevent a crash signal being generated in the event of a rear-end collision. As a result automatic unlocking of the doors and switching on of the hazard lamps cannot be assured. Fix: The recalled vehicles will have the airbag control unit replaced. | 1 |
| Feb 2007 | Suspension spring may fractureFault: It has been identified that during manufacture insufficient wax was applied to the front of the rear axle road springs. This in extreme circumstances can lead to failure of the spring. Fix: Recalled vehicles will have the rear road spring front mounting brackets replaced. | 4 |
| Feb 2007 | Electrical short circuit may occurFault: Wiring harness from starter to alternator may detach power supply will fail and wiring may short circuit. Fix: Recall affected vehicles check and if necessary replace harness. | 1,145 |
| Jan 2007 | Wheel flanges may splitFault: The wheel flanges may not be of sufficient strength and may split. Fix: Recall the vehicles that are likely to be affected to fit modified wheels. | 1 |
| Jun 2006 | Seat belt may become insecureFault: It is possible that the mounting bolts for rear seat belts on the rear seats may not have been torqued to the correct specification. Fix: Recall all affected vehicles to check and if necessary re-torque the mounting bolts. | 1 |
| Jun 2004 | Tyre valves may leak where fitted in wheel.Fault: The tyre valve may not be to specification and could leak at its fitting in the wheel. Fix: Recall the affected vehicles and fit new tyre valves that comply with the specification. | 113 |
| Aug 2003 | Possible fault in air bag control moduleFault: A component inside the control module may become defective - Air bag may not deploy in a collision Fix: Replace Air Bag control module. | 29 |
| Dec 2000 | Brake imbalanceFault: The rear axle load sensing valve may become defective resulting in uneven braking effort between the left and right hand rear wheels. Fix: Recall vehicles check and if required replace the load sensing (ALB) valve. | 739 |
Nothing matches that search on this page.
Vehicles affected is the number DVSA lists for each recall.
How to check a car for recalls
A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.
A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.
Frequently asked questions
How do I check if my Sprinter has an outstanding recall?
Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.
How many recalls has the Mercedes-Benz Sprinter had?
DVSA's recalls data lists 124 safety recalls covering the Mercedes-Benz Sprinter, the most recent dated 19 December 2025. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Does a recall mean a car is unreliable?
No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
What should I do if my car is affected by a recall?
Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.
Where does this recall data come from?
From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.
Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.
Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.
Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.
Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.
What it can do
- ✓Free vehicle check: send any UK reg for the make, model, MOT and tax status, plus any outstanding safety recall
- ✓Snap a number plate: send a photo and we read the reg for you, then ask you to confirm it
- ✓Free valuation: add the mileage after the reg, for example AB12 CDE 45k. A guide only, not an offer to buy or a guarantee of sale price See terms
- ✓Paid vehicle history check, with data provided by Experian, delivered in the chat
- ✓Free MOT and tax reminders: reply REMIND with a reg (typos are fine)
- ✓Recalls: send RECALLS and a make or model, for example RECALLS Ford Puma
- ✓MOT pass rates: send MOT RATE and a model, for example MOT RATE Ford Fiesta
- ✓How many are left: send HOW MANY and a model no longer sold new, for example HOW MANY Saab 9-3
- ✓Find a vehicle: tell us what you want, for example Ford Fiesta under 8k
- ✓Ask about a vehicle: send its MotifyMe link or reg with your question, or after a search reply ASK, the number and your question, for example ASK 2 is it still available
- ✓Fuel prices: live prices, plus a journey fuel cost such as London to Edinburgh
- ✓Fuel price alerts by email: send FUEL ALERT with your town or postcode, fuel and email address
- ✓Diesel driver? Send FUEL CARD for the Accelerate diesel fuel card, up to 5p a litre
- ✓Reply STOP at any time to opt out
Looking for a Mercedes-Benz Sprinter?
See used Mercedes-Benz Sprinter cars listed on the MotifyMe® marketplace.
See Sprinter cars for sale