BMW 1 Series Recalls

Safety recalls covering the BMW 1 Series in DVSA's recalls data, newest first.

Last updated 22 November 2026

Short answer:

DVSA's recalls data lists 39 safety recalls covering the BMW 1 Series, the most recent dated 12 January 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.

Check a registration for outstanding recalls, free

39Recalls listed
12 January 2026Latest recall
29 September 2004Earliest listed
3,862,997Vehicles affected

Every BMW 1 Series recall

Open a recall to see the fault, the fix and the build dates it covers.

DateRecallVehicles affected
Jan 2026
Replace the driver’s airbag - takata psdi-5

Fault: Affected vehicles may be fitted with a drivers airbag which may deploy with too much explosive force causing sharp metal fragments to be released into the cabin. It has the potential to fatally or seriously injure vehicle occupants.

Fix: Affected vehicles will have the airbag replaced.

Recall R/2025/327 · Dated 12 January 2026 · Built 7 January 2006 to 8 October 2013

139,753
Dec 2025
Takata driver and/or passenger airbag recall (global vins)

Fault: Affected vehicles are already included in Safety Recalls within the markets they have previously resided in. The vehicles may be fitted with a driver and/or passenger airbag/s which if deployed may do so with excessive force causing sharp metal fragments to be released this may cause serious injury which could prove fatal to people in the vicinity.

Fix: Vehicles will have the affected airbags checked and if necessary replaced.

Recall R/2025/349 · Dated 18 December 2025 · Built 15 April 2004 to 4 November 2017

5,637
Oct 2025
Replace the engine starter motor

Fault: For affected vehicles there is a concern involving water ingress and corrosion to the starter motor for where a short circuit cannot be ruled out. It is strongly recommended to park the vehicle outdoors and not in the immediate vicinity of buildings until the repair has been carried out.

Fix: Replacement of the starter motor.

Recall R/2025/405 · Dated 27 October 2025 · Built 22 February 2017 to 29 May 2019

9,310
Oct 2025
Seat belt rear outer seats

Fault: On affected vehicles either one or both of the outer most rear seats may not have been manufactured correctly and the sensitivity sensor may be deformed. If the sensor is not functioning correctly there is a risk the seat belt may not operate as intended.

Fix: On affected vehicles the affected seatbelts will be checked and replaced.

Recall R/2025/443 · Dated 23 October 2025 · Built 7 August 2025 to 30 September 2025

4,423
Jul 2025
Checking the threaded connection of grounding cable pcu48

Fault: On affected vehicles the ground connection cable on the 48V power supply control unit may not have been torqued to the correct specification.

Fix: Affected vehicles will have the ground connection checked and re-torqued. If required the relevant cable and Power Control Unit will be replaced.

Recall R/2025/267 · Dated 18 July 2025 · Built 19 June 2025 to 25 June 2025

270
Nov 2024
Rework front end threaded connection (BMW)

Fault: On affected vehicles the screws connecting the front end to the vehicles body may have been tightened to a torque level lower than required.

Fix: The screws will be replaced if necessary and correctly torqued.

Recall R/2024/452 · Dated 8 November 2024 · Built 4 April 2023 to 10 May 2024

9
Oct 2024
Check driver’s airbag for conversion takata sdi & psdi-5

Fault: Affected vehicles may have had a retrofit or conversion of the airbag using a previously recalled airbag variant which if deployed may do so with excessive force causing sharp metal fragments to be released this may cause serious injury possibly fatal to people in the vicinity. The original factory fitment airbag for the vehicle is not affected.

Fix: Vehicles will have the airbag checked and if necessary replaced.

Recall R/2024/403 · Dated 21 October 2024 · Built 15 April 2004 to 8 November 2017

172,517
Sep 2024
Integrated braking system

Fault: On certain vehicles the Integrated Brake (IB) system may be impaired due to contamination between electrical contacts.

Fix: Vehicles that may be affected by contamination are required to have the vehicle's software updated which can detect signal interference before it occurs. If symptoms are detected you should refrain from use of the vehicle and the affected Integrated Brake (IB) system component will be replaced.

Recall R/2024/383 · Dated 13 September 2024 · Built 4 September 2023 to 4 September 2023

2
May 2024
Replace vanos bolts n51 n52 n55

Fault: On affected vehicles overtime the aluminium screws can loosen or break on the adjustable variable camshaft timing (VANOS) units potentially resulting in engine emergency mode being activated.

Fix: On affected vehicles the eight aluminium screws will be replaced if evidence of faulty screws is found then the VANOS adjustment unit will also be replaced.

Recall R/2024/191 · Dated 1 May 2024 · Built 30 September 2009 to 22 July 2011

439
Mar 2024
Replacing the driver’s airbag psdi-5

Fault: On affected vehicles a possible degradation due to age of the propellant tablets may lead to over aggressive combustion if the air bag is activated and cause the inflator body to rupture.

Fix: On the affected vehicles the drivers air bag will be replaced.

Recall R/2024/132 · Dated 18 March 2024 · Built 15 April 2004 to 22 December 2005

19,190
Jan 2023
A possible degradation of the propellant tablets could lead to an over-aggressive combustion in the event the airbag is activated which may cause the inflator body to rupture.

Fault: A possible degradation of airbag propellant tablets could lead to an over-aggressive combustion in the event the airbag is activated which may cause the inflator body to rupture.

Fix: On affected vehicles the drivers airbag module will be replaced.

Recall R/2023/016 · Dated 24 January 2023 · Built 22 October 2013 to 30 June 2017

39,227
Aug 2022
Undetected EGR system leaks may cause thermal activity in the intake manifold

Fault: Undetected EGR System leaks may cause thermal activity in the intake manifold.

Fix: The engine management control unit (DDE) will be programmed with improved software incorporating the latest OBD functionality.

Recall R/2022/255 · Dated 22 August 2022 · Built 12 February 2015 to 1 March 2018

645,490
Aug 2022
The exhaust gas recirculation cooler may leak over time and cause thermal incident

Fault: The Exhaust Gas Recirculation cooler may leak over time and cause thermal incident.

Fix: On the affected vehicles the EGR cooler module will be replaced.

Recall R/2022/206 · Dated 1 August 2022 · Built 3 November 2011 to 3 June 2019

638,798
Dec 2021
The material quality of the screws used for SEAT belts and rear seats may not be to specifications.

Fault: The material quality of seat and seatbelt screws may not be according to specification.

Fix: On the affected vehicles the screws will be replaced in specific locations on the seat belts or rear seats.

Recall R/2021/442 · Dated 29 December 2021 · Built 22 October 2021 to 27 October 2021

38
Mar 2021
The blower regulator wiring could be damaged and could lead to partial contact of individual wire strands

Fault: The blower-regulator wiring could be damaged and could lead to partial contact of individual wire strands.

Fix: The blower regulator wiring harness will be inspected and a new part will be installed additional components will be replaced if necessary.

Recall R/2021/064 · Dated 15 March 2021 · Built 15 April 2004 to 22 May 2011

724,044
Feb 2021
The exhaust gas recirculation cooler could leak over time

Fault: Leaking glycol coolant could create in combination with soot and oil sediments in the EGR module ignitable deposits.

Fix: The EGR cooler will be internally inspected with an endoscope and replaced if evidence of leaking is found.

Recall R/2021/037 · Dated 9 February 2021 · Built 28 February 2015 to 15 October 2018

127,776
Aug 2020
The exhaust gas recirculation module cooler could leak over time

Fault: The Exhaust Gas Recirculation (EGR) Module cooler could leak over time

Fix: The EGR cooler will be inspected on the affected vehicles and replaced if evidence of leaking is found.

Recall R/2020/179 · Dated 17 August 2020 · Built 21 October 2014 to 26 June 2017

142,256
Jul 2020
Camshaft support housing bearing caps may become loose

Fault: It is possible that the camshaft bearing cap screws could come loose on the affected vehicles.

Fix: Check and replace camshaft support housing or complete cylinder head as required.

Recall R/2020/191 · Dated 27 July 2020 · Built 18 February 2020 to 28 February 2020

39
Apr 2020
The driver's air bag fabric could be damaged by the air bag cover during deployment

Fault: This airbag fabric could be damaged by the airbag cover during deployment.

Fix: On the affected vehicles the driver�s airbag will be replaced.

Recall R/2020/110 · Dated 27 April 2020 · Built 28 January 2020 to 11 March 2020

1,121
Dec 2018
Exhaust gas recirculation module cooler could leak

Fault: The EGR cooler may leakpresenting a fire risk

Fix: A visual inspection of the EGR cooler to check for leaks and excessive build-up of deposits. The EGR cooler will be replaced on all affected vehicles

Recall R/2018/341 · Dated 7 December 2018 · Built 3 November 2011 to 26 February 2015

450,898
Nov 2018
Exhaust gas recirculation cooler could potentially leak over time

Fault: The EGR cooler may leakpresenting a fire risk.

Fix: The EGR cooler will be replaced with an improved version.

Recall R/2018/258 · Dated 5 November 2018 · Built 29 July 2014 to 18 September 2017

307,204
Oct 2018
Software fault in crankshaft sensor

Fault: The affected vehicles may be equipped with a crankshaft sensor with a software fault.

Fix: On the affected vehicles the crankshaft sensor will be replaced with a new version.

Recall R/2018/260 · Dated 15 October 2018 · Built 16 May 2018 to 28 May 2018

3,284
Aug 2018
Software fault with crankshaft sensor

Fault: The affected vehicles may be equipped with a crankshaft sensor with a software fault. The crankshaft sensor cannot process the signal values from the crankshaft transmitter due to an improper firmware level. The firmware does not compensate sufficiently the temperature gradients and the magnetic field strength of the sensor electronic. If the crankshaft sensor cannot process the signal values from the transmitter the Digital Diesel Electronic (DDE) will notice that and change to the emergency operation mode. The emergency mode will be displayed by the check control message �engine malfunction�. The driver may notice a rough running engine and a reduced driving power (70%). However an engine stalling during driving conditions cannot be excluded.

Fix: On the affected vehicles the crankshaft sensor will be replaced with a new version.

Recall R/2018/211 · Dated 20 August 2018 · Built 22 May 2018 to 13 July 2018

8,050
Jun 2018
Plug in contact cable may malfunction

Fault: The positive battery cable to the front distribution box behind the glove box can become damaged by vibrations and frictional corrosion. This may cause a loss of electrical connection to the distributions box. Symptoms include being unable to gain entry or start the car but the most common are a flickering instrument panel or uneven engine performance. However if the electrical connection is completely lost this will also affect the operation of the vehicles lighting systems; e.g. sidelights or hazard warning lamps.

Fix: On affected vehicles carry out a suitable repair to the battery cable positive cable.

Recall R/2018/132 · Dated 7 June 2018 · Built 24 October 2006 to 30 June 2011

311,848
Feb 2018
Backrest could fold forward under heavy load

Fault: The latching element of the Easy Entry Kit on the driver's seat does not lock correctly into the lower swinging arm. As a result the backrest could fold under heavy load such as in a collision or unsecured load in the rear and harsh braking.

Fix: The vehicle that is likely to be affected will be recalled and a new seat mechanism fitted. R/2018/027 refers.

Recall R/2018/027 · Dated 5 February 2018

1
Apr 2017
Driveshaft universal joint may break

Fault: Due to insufficient strength the front universal joint in the rear front universal joint of the rear prop shaft may fail.

Fix: On affected vehicle replace the universal joint with a modified version

Recall R/2017/132 · Dated 11 April 2017 · Built 20 December 2010 to 29 April 2011

21,698
Apr 2017
Plug in contact cable may malfunction

Fault: It is possible that the connection between the B+ cable and the Power Distribution Box can become damaged by wear and heat which is caused by high current flow and high contact resistance. Normally this will result in a non-start situation after parking the vehicle. However it is possible that this could in extreme cases occur whilst the vehicle is in motion. The driver should be made aware of the issue by flickering of the instrument cluster (dash) or an engine mis-fire; but if the driver does not then the engine could cut-out without warning.

Fix: Recall all affected vehicles with petrol engines and replace the cable/connection with a more robust item.

Recall R/2017/114 · Dated 10 April 2017 · Built 1 December 2009 to 13 October 2011

36,410
Dec 2016
Power steering may not perform correctly

Fault: The electrical contact of the Electronic Control Unit (ECU) of the Electric Power Steering (EPS) is not sufficiently robust over the service life of the vehicle. As a result the power steering support may fail possibly leading to disconcerting driving situation for the driver. Additionally in a few cases a localised thermal event cannot be excluded.

Fix: Recall the vehicles that are likely to be affected and replace the steering gear (EPS).

Recall R/2016/300 · Dated 21 December 2016 · Built 19 September 2011 to 8 December 2015

41
Jun 2015
Engine may stall

Fault: The in tank fuel pump may contain sub components that have not been correctly nickel plated. This may cause excessive friction leading to the fuel pump being inoperative. The driver may experience a no start condition or in the worst case an engine stall. A warning lamp and error message will display. Steering and brakes will still function.

Fix: Recall the vehicles that are likely to be affected and replace the in tank fuel pump with a modified version.

Recall R/2015/109 · Dated 8 June 2015 · Built 1 September 2013 to 31 March 2015

3,292
Jul 2014
Engine emergency mode may be activated during driving

Fault: The screws retaining the variable camshaft timing (VANOS) housing may loosen and under certain circumstances the heads may break off. This can lead to the VANOS leaking oil internally and adversely affect the valve timing adjustment. If found to deviating from targeted data the engine emergency mode will be activated. This will be indicated by a distinct change in engine running. The orange engine management warning lamp and a check message; On vehicles with N51/N52 engines this will appear at ignition recycle on N55 engine it will display immediately.

Fix: Repalce bolted connection of the VANOS adjustment unit

Recall R/2014/068 · Dated 28 July 2014 · Built 1 September 2009 to 30 November 2011

2,967
Sep 2013
Possibility of fire

Fault: Due to a fault with an internal connection within the Fuel Filter Heater (FFH) it is possible that during temperatures below freezing the FFH can remain permanently activated. This will normally cause the FFH to overheat which will result in the inability to start the vehicle due to a flat battery. This can occur even when the ignition is turned off. However in extreme cases it could cause a vehicle fire.

Fix: Recall all affected vehicles to replace the FFH.

Recall R/2013/095 · Dated 10 September 2013 · Built 1 May 2009 to 30 November 2009

21,502
Jul 2013
Loss of drive

Fault: It is possible that over a period of time the bolt securing the clutch cover/pressure plate may become loose. The drive should be warned of this by the behaviour of the clutch noise from it or inability to select gears. Under certain conditions complete loss of drive could occur which could place the driver and occupant of the vehicle in a prone position.

Fix: Recall all affected vehicles and replace the clutch bolts.

Recall R/2013/080 · Dated 5 July 2013 · Built 1 February 2013 to 30 June 2013

4
Apr 2013
Engine may cut out

Fault: It is possible that the connection between the B+ cable and the Power Distribution Box can become damaged by wear and heat which is caused by high current flow and high contact resistance. Normally this will result in a non-start situation after parking the vehicle. However it is possible that this could in extreme cases occur whilst the vehicle is in motion. The driver should be make aware of the issue by flickering of the instrument cluster (dash) or an engine mis-fire; but if the driver does not then the engine could cut-out without warning.

Fix: Recall all affected vehicles and replace the cable/connection with a more robust item.

Recall R/2013/024 · Dated 4 April 2013

36
Jul 2012
Eps may not perform as specified

Fault: Due to a component in the integrated control module not being to specification it is possible power steering assistance may fail. If this happens the EPS warning lamp will illuminate and a check control message will appear on the dashboard display. Directional control will be maintained albeit with additional driver input.

Fix: Recall vehicles likely to be affected to replace the steering box.

Recall R/2012/081 · Dated 30 July 2012 · Built 1 June 2007 to 31 December 2011

1,402
Oct 2011
Risk of fire

Fault: Moisture may enter the fuel filter heater at an electrical connection. Should this occur it can cause a discharge of the battery causing non starting of the vehicle. Also if it occurs whilst the vehicle is in motion it could result in a fire when the vehicle is left unattended.

Fix: Recall all affected vehicles and replace the fuel filter heater.

Recall R/2011/123 · Dated 5 October 2011 · Built 20 August 2008 to 12 June 2009

21,923
Aug 2010
Fire may occur

Fault: The top seat belt automatic reel with pyrotechnic ignited pre-tensioner fitted is mounted too close to the sound insulation both nearside and offside. If the vehicle is involved in a substantial collision where the pre-tensioners are deployed a fire may occur as it is possible for the hot gases to ignite the sound insulation.

Fix: Recall the vehicles that are likely to be affected to rework the sound insulation fitted to both nearside and offside and if necessary fit new top seat belts

Recall R/2010/102 · Dated 4 August 2010 · Built 1 November 2006 to 31 May 2010

25
Jun 2009
Front side airbag or SEAT belt tensioner may not operate correctly

Fault: It has been identified that due to faulty crimping of the component parts of the airbag wiring harness and seat belt tensioner the side airbag or seatbelt tensioner may not trigger in the vent of a collision.

Fix: Recalled vehicles will have the harness checked and repaired as necessary.

Recall R/2009/065 · Dated 30 June 2009 · Built 23 May 2008 to 21 July 2008

1,756
Nov 2006
Possible loss of braking power assistance

Fault: A temporary fault in the greasing system on the brake servo sealing ring could lead to the sealing ring being subject to wear. In unfavourable conditions the seal may be pressed into the brake servo housing as a consequence of increased friction. The arising leak will cause a hissing sound audible within the vehicle interior with the additional consequence that there may be a risk that loss of brake assistance will ensue.

Fix: Recalled vehicles will have the brake servo replaced.

Recall R/2006/207 · Dated 28 November 2006 · Built 4 March 2006 to 14 March 2006

287
Sep 2004
Connections on the control arm to the rear axle may become loose

Fault: The rear axle control arms may not have been fitted as intended. In consequence the connections on the control arms concerned may become loose causing unacceptable lateral forces to be applied to the securing bolts. In this situation exact alignment of the wheels can no longer be guaranteed.

Fix: Recalled vehicles will have the subject control arms checked for correct alignment and if found not to have been fitted as intended they may require to be replaced.

Recall R/2004/172 · Dated 29 September 2004 · Built 19 May 2004 to 8 September 2004

30

Nothing matches that search on this page.

Vehicles affected is the number DVSA lists for each recall.

How to check a car for recalls

A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.

A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.

Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.

Frequently asked questions

How do I check if my 1 Series has an outstanding recall?

Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.

How many recalls has the BMW 1 Series had?

DVSA's recalls data lists 39 safety recalls covering the BMW 1 Series, the most recent dated 12 January 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.

Does a recall mean a car is unreliable?

No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.

What should I do if my car is affected by a recall?

Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.

Where does this recall data come from?

From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.

Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.

Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.

Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.

Free vehicle check on WhatsApp

Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.

Open WhatsApp

How it works

Looking for a BMW 1 Series?

See used BMW 1 Series cars listed on the MotifyMe® marketplace.

See 1 Series cars for sale