BMW 3 Series Recalls

Safety recalls covering the BMW 3 Series in DVSA's recalls data, newest first.

Last updated 22 November 2026

Short answer:

DVSA's recalls data lists 66 safety recalls covering the BMW 3 Series, the most recent dated 2 March 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.

Check a registration for outstanding recalls, free

66Recalls listed
2 March 2026Latest recall
28 February 1992Earliest listed
7,501,811Vehicles affected

Every BMW 3 Series recall

Open a recall to see the fault, the fix and the build dates it covers.

DateRecallVehicles affected
Mar 2026
Replace the engine starter motor

Fault: The Safety Recall relates to the engine starter motor. The fault relates to the RSW22 starter RWT (reinforced water tightness). It was found that with RWT starters an increased abrasion of the magnetic contact can cause the growth of deposits at the lowest point of the relay interior. This in turn may increase the relay contact resistance resulting in false starts or even causing short circuits and possibly a thermal reaction. In case of a short circuit the possibility of a thermal event cannot be excluded. This may happen while attempting to start the vehicle or while driving due to vibrations causing a short circuit due to moving deposits.

Fix: On the affected vehicles the starter motor will be replaced with a variant by another supplier with a different design. Until the repair has been completed it is recommended to not leave the vehicle running unattended after starting the engine.

Recall R/2026/054 · Dated 2 March 2026 · Built 18 September 2020 to 29 April 2025

24,004
Jan 2026
Replace the driver’s airbag - takata psdi-5

Fault: Affected vehicles may be fitted with a drivers airbag which may deploy with too much explosive force causing sharp metal fragments to be released into the cabin. It has the potential to fatally or seriously injure vehicle occupants.

Fix: Affected vehicles will have the airbag replaced.

Recall R/2025/327 · Dated 12 January 2026 · Built 2 January 2006 to 2 October 2013

177,298
Dec 2025
Takata driver and/or passenger airbag recall (global vins)

Fault: Affected vehicles are already included in Safety Recalls within the markets they have previously resided in. The vehicles may be fitted with a driver and/or passenger airbag/s which if deployed may do so with excessive force causing sharp metal fragments to be released this may cause serious injury which could prove fatal to people in the vicinity.

Fix: Vehicles will have the affected airbags checked and if necessary replaced.

Recall R/2025/349 · Dated 18 December 2025 · Built 30 October 1997 to 8 November 2017

43,344
Oct 2025
Replace the engine starter motor

Fault: For affected vehicles there is a concern involving water ingress and corrosion to the starter motor for where a short circuit cannot be ruled out. It is strongly recommended to park the vehicle outdoors and not in the immediate vicinity of buildings until the repair has been carried out.

Fix: Replacement of the starter motor.

Recall R/2025/405 · Dated 27 October 2025 · Built 26 October 2015 to 21 June 2021

36,549
Oct 2025
Replace the front passenger airbag takata pspi

Fault: For vehicles fitted with a Takata front passenger airbag with a PSPI inflator these vehicles have previously received a like for like replacement front passenger airbag via a previous safety recall campaign.

Fix: The front passenger airbag module of the affected vehicles will now be replaced by an airbag module or an inflator that does not contain ammonium nitrate.

Recall R/2025/323 · Dated 6 October 2025 · Built 3 May 1999 to 24 August 2006

102,611
Oct 2024
Check driver’s airbag for conversion takata sdi & psdi-5

Fault: Affected vehicles may have had a retrofit or conversion of the airbag using a previously recalled airbag variant which if deployed may do so with excessive force causing sharp metal fragments to be released this may cause serious injury possibly fatal to people in the vicinity. The original factory fitment airbag for the vehicle is not affected.

Fix: Vehicles will have the airbag checked and if necessary replaced.

Recall R/2024/403 · Dated 21 October 2024 · Built 15 October 2004 to 8 November 2017

218,198
Sep 2024
Replace the passenger airbag

Fault: On certain vehicles the passenger airbag may not have had the seam sewn according to the specifications.

Fix: Replacement of the passenger airbag

Recall R/2024/428 · Dated 24 September 2024 · Built 16 July 2024 to 22 July 2024

16
May 2024
Replace vanos bolts n51 n52 n55

Fault: On affected vehicles overtime the aluminium screws can loosen or break on the adjustable variable camshaft timing (VANOS) units potentially resulting in engine emergency mode being activated.

Fix: On affected vehicles the eight aluminium screws will be replaced if evidence of faulty screws is found then the VANOS adjustment unit will also be replaced.

Recall R/2024/191 · Dated 1 May 2024 · Built 23 October 2009 to 8 June 2011

19
Mar 2024
Replacing the driver’s airbag psdi-5

Fault: On affected vehicles a possible degradation due to age of the propellant tablets may lead to over aggressive combustion if the air bag is activated and cause the inflator body to rupture.

Fix: On the affected vehicles the drivers air bag will be replaced.

Recall R/2024/132 · Dated 18 March 2024 · Built 7 December 2004 to 30 December 2005

7,682
Dec 2023
On affected vehicles ingress of transmission fluid may occur to the integrated transmission control unit within the mechatronic module

Fault: On affected vehicles ingress of transmission fluid may occur to the integrated transmission control unit within the mechatronic module

Fix: On affected vehicles the transmission mechatronic module will be replaced

Recall R/2023/354 · Dated 20 December 2023 · Built 24 January 2023 to 24 January 2023

26
Mar 2023
On certain vehicles the body domain controller (BDC) control unit may have an incorrect setting applied to it.

Fault: On certain vehicles the Body Domain Controller (BDC) control unit may have an incorrect setting applied to it.

Fix: Conduct a check of the settings and if necessary perform a reset on the BDC control unit.

Recall R/2023/071 · Dated 20 March 2023 · Built 4 July 2022 to 22 October 2022

538
Jan 2023
A possible degradation of the propellant tablets could lead to an over-aggressive combustion in the event the airbag is activated which may cause the inflator body to rupture.

Fault: A possible degradation of airbag propellant tablets could lead to an over-aggressive combustion in the event the airbag is activated which may cause the inflator body to rupture.

Fix: On affected vehicles the drivers airbag module will be replaced.

Recall R/2023/016 · Dated 24 January 2023 · Built 13 June 2012 to 30 June 2017

92,048
Nov 2022
It is possible that a damaged SEAT belt may have been installed into the vehicle during production.

Fault: It is possible that a damaged seat belt may have been installed into the vehicle during production.

Fix: The front left upper seat belt will be replaced on affected vehicles as a precaution.

Recall R/2022/323 · Dated 9 November 2022 · Built 12 September 2022 to 12 September 2022

7
Oct 2022
Manufacturing defect with winding of cell-internal films for high voltage battery

Fault: The safety recall relates to a problem with a cell module within the high-voltage battery.

Fix: Replace the affected high-voltage cell module.

Recall R/2022/297 · Dated 17 October 2022 · Built 11 January 2021 to 11 January 2021

1
Sep 2022
In rare cases the starter motor can inadvertently be activated permanently presenting a risk of a thermal event

Fault: In rare cases the starter motor can inadvertently be activated permanently presenting a risk of a thermal event.

Fix: Rework the starter motor assembly.

Recall R/2022/261 · Dated 12 September 2022 · Built 15 September 2015 to 31 July 2018

25,982
Aug 2022
Undetected EGR system leaks may cause thermal activity in the intake manifold

Fault: Undetected EGR System leaks may cause thermal activity in the intake manifold.

Fix: The engine management control unit (DDE) will be programmed with improved software incorporating the latest OBD functionality.

Recall R/2022/255 · Dated 22 August 2022 · Built 3 December 2014 to 12 July 2021

1,613,725
Aug 2022
The exhaust gas recirculation cooler may leak over time and cause thermal incident

Fault: The Exhaust Gas Recirculation cooler may leak over time and cause thermal incident.

Fix: On the affected vehicles the EGR cooler module will be replaced.

Recall R/2022/206 · Dated 1 August 2022 · Built 9 December 2011 to 21 November 2019

958,197
Mar 2022
The micro gas generator within the front seatbelt's retractor may have been damaged

Fault: The micro gas generator within the front seatbelt�s retractor may have been damaged and may not act according to the specification in the event of an accident.

Fix: On the affected vehicles the front seatbelts will be checked and replaced if they are found to have been damaged

Recall R/2022/089 · Dated 30 March 2022 · Built 26 January 2022 to 26 January 2022

2,018
Dec 2021
Excessive increase of cooling system temperature could lead to a bursting of the heater matrix radiator

Fault: Excessive increase of cooling system temperature could (in a worst case) lead to a bursting of the heater matrix radiator.

Fix: Fitting an additional thermostat and modified hoses into the heating system to bypass the heat exchanger if overheating was to occur.

Recall R/2021/430 · Dated 13 December 2021 · Built 1 March 1987 to 1 May 1992

66
Aug 2021
The tandam vacuum/oil pump may fail

Fault: The fault involves the tandem vacuum/oil pump fitted to the engine. On affected vehicles it is possible that the engine rotates in the opposite direction than it is meant to on start-up causing the tandem pump to fail.

Fix: On the affected vehicles the control unit (DME) will be programmed to prevent the failure from occuring.

Recall R/2021/288 · Dated 9 August 2021 · Built 13 April 2019 to 13 April 2019

1
Jul 2021
Some vehicles may be susceptible to damage to the anti-corrosion coating of the lower steering shaft

Fault: Some vehicles may be susceptible to damage to the anti-corrosion coating of the lower steering shaft.

Fix: On the affected vehicles the steering shaft must be replaced.

Recall R/2021/268 · Dated 13 July 2021 · Built 1 August 1990 to 24 August 2000

277,987
Jun 2021
The exhaust gas recirculation module could leak over time

Fault: The Exhaust Gas Recirculation (EGR) Module could leak over time�and cause thermal incident.

Fix: The EGR cooler will be internally inspected with an endoscope and replaced if evidence of leaking is found.

Recall R/2021/213 · Dated 14 June 2021 · Built 10 March 2017 to 1 October 2018

54,990
May 2021
The screw connection of the front SEAT belt buckle assembly to the SEAT frame may not be tightened properly

Fault: The screw connection of the front seat belt buckle assembly to the seat frame may not be tightened properly.

Fix: On affected vehicles the screw connection of the lower belt of the front seats will be checked and if necessary reworked.

Recall R/2021/168 · Dated 17 May 2021 · Built 4 September 2020 to 11 March 2021

120
Mar 2021
Affected vehicles may be fitted with brake discs which are not to specification

Fault: Affected vehicles may be fitted with brake discs which were not produced according to the specifications

Fix: On the affected vehicles the brake discs will be checked and if necessary replaced

Recall R/2021/085 · Dated 15 March 2021 · Built 27 January 2021 to 3 February 2021

705
Feb 2021
The exhaust gas recirculation cooler could leak over time

Fault: Leaking glycol coolant could create in combination with soot and oil sediments in the EGR module ignitable deposits.

Fix: The EGR cooler will be internally inspected with an endoscope and replaced if evidence of leaking is found.

Recall R/2021/037 · Dated 9 February 2021 · Built 30 June 2015 to 17 September 2018

191,664
Jan 2021
The battery cables on the 48v starter generator may not have been sufficiently secured during production

Fault: The battery cables on the 48V starter generator may not have been sufficiently secured during the production process.

Fix: Check the screw connection of the 48V positive / negative battery cables on the starter generator and rework if necessary.

Recall R/2021/015 · Dated 25 January 2021 · Built 24 February 2020 to 26 October 2020

776
Dec 2020
Remaining particles in the cells of the high voltage battery can cause a short circuit

Fault: A possibility of impurities contained in the HV batteries may cause short circuit.

Fix: Testing of battery charge cycles and replacement of the HV cells where necessary.

Recall R/2020/283 · Dated 14 December 2020 · Built 3 March 2020 to 22 September 2020

5,330
Oct 2020
Remaining particles in the cells of the high voltage battery can cause a short circuit

Fault: In very rare cases welding beads were not always completely removed in the cleaning process during battery production.

Fix: Test and replace the High Voltage batteries if affected.

Recall R/2020/298 · Dated 22 October 2020 · Built 27 January 2020 to 30 September 2020

1,742
Aug 2020
Steering tie rod can become broken in the 'kink' groove area of the rod

Fault: A steering tie rod with an earlier design configuration can become broken in the �kink� groove area of the rod.

Fix: Both of the steering tie rods will be replaced on the affected vehicles.

Recall R/2020/219 · Dated 10 August 2020 · Built 22 October 2018 to 16 March 2019

4,542
Apr 2020
The foldable rear centre head restraint interlock was not welded according to specifications

Fault: The rear center head restraint interlock was not welded according to specification.

Fix: On the affected vehicles the center rear head restraint will be replaced.

Recall R/2019/290 · Dated 7 April 2020 · Built 5 July 2019 to 31 July 2019

1,737
Mar 2020
Driver's front takata (NADI) airbag inflator may rupture on deployment

Fault: Drivers air bag may deploy incorrectly

Fix: Replace the air bag inflators.

Recall R/2019/403 · Dated 9 March 2020 · Built 28 October 1997 to 10 July 2000

67,548
Dec 2019
The pressing force of the bearing bushing into the crankcase may be out of specification

Fault: The engine counterbalance shaft bearing bushing into the crankcase may be out of specification

Fix: Replace the engine of affected vehicles

Recall R/2019/368 · Dated 9 December 2019 · Built 11 March 2019 to 9 July 2019

53
Mar 2019
Potential rupture of driver front air bag inflator

Fault: The front drivers air bag may not deploy correctly on activation.

Fix: Check and replace the drivers front air bag if required.

Recall R/2019/086 · Dated 22 March 2019 · Built 28 September 1999 to 29 December 2001

6,927
Dec 2018
Exhaust gas recirculation module cooler could leak

Fault: The EGR cooler may leakpresenting a fire risk

Fix: A visual inspection of the EGR cooler to check for leaks and excessive build-up of deposits. The EGR cooler will be replaced on all affected vehicles

Recall R/2018/341 · Dated 7 December 2018 · Built 9 December 2011 to 11 April 2017

676,347
Nov 2018
Exhaust gas recirculation cooler could potentially leak over time

Fault: The EGR cooler may leakpresenting a fire risk.

Fix: The EGR cooler will be replaced with an improved version.

Recall R/2018/258 · Dated 5 November 2018 · Built 19 March 2015 to 22 November 2017

460,806
Oct 2018
Software fault in crankshaft sensor

Fault: The affected vehicles may be equipped with a crankshaft sensor with a software fault.

Fix: On the affected vehicles the crankshaft sensor will be replaced with a new version.

Recall R/2018/260 · Dated 15 October 2018 · Built 16 May 2018 to 7 June 2018

4,926
Aug 2018
Software fault with crankshaft sensor

Fault: The affected vehicles may be equipped with a crankshaft sensor with a software fault. The crankshaft sensor cannot process the signal values from the crankshaft transmitter due to an improper firmware level. The firmware does not compensate sufficiently the temperature gradients and the magnetic field strength of the sensor electronic. If the crankshaft sensor cannot process the signal values from the transmitter the Digital Diesel Electronic (DDE) will notice that and change to the emergency operation mode. The emergency mode will be displayed by the check control message �engine malfunction�. The driver may notice a rough running engine and a reduced driving power (70%). However an engine stalling during driving conditions cannot be excluded.

Fix: On the affected vehicles the crankshaft sensor will be replaced with a new version.

Recall R/2018/211 · Dated 20 August 2018 · Built 18 May 2018 to 7 June 2018

12,075
Jun 2018
Variation to electrical resistance in the blower regulator wiring harness connector

Fault: Over time irregularities in the crimp connection in conjunction with relative movements of the tin coated connector at the end of the wiring harness which connects to the tin coated blower regulator pin could lead to frictional corrosion. In combination with very high current flow which would occur which could lead to a temperature increase. As a result the blower regulator wiring could be damaged and could lead to partial contact of individual wire strands. this could result in an irregular current flow further overheating and increase the risk of fire.

Fix: The blower regulator wiring harness will be inspected and a new part will be installed.

Recall R/2018/148 · Dated 27 June 2018 · Built 15 October 2004 to 8 July 2011

1,116,416
Jun 2018
Plug in contact cable may malfunction

Fault: The positive battery cable to the front distribution box behind the glove box can become damaged by vibrations and frictional corrosion. This may cause a loss of electrical connection to the distributions box. Symptoms include being unable to gain entry or start the car but the most common are a flickering instrument panel or uneven engine performance. However if the electrical connection is completely lost this will also affect the operation of the vehicles lighting systems; e.g. sidelights or hazard warning lamps.

Fix: On affected vehicles carry out a suitable repair to the battery cable positive cable.

Recall R/2018/132 · Dated 7 June 2018 · Built 20 September 2006 to 30 June 2011

311,848
Apr 2017
Driveshaft universal joint may break

Fault: Due to insufficient strength the front universal joint in the rear front universal joint of the rear prop shaft may fail.

Fix: On affected vehicle replace the universal joint with a modified version

Recall R/2017/132 · Dated 11 April 2017 · Built 30 December 2010 to 29 April 2011

10,849
Apr 2017
Plug in contact cable may malfunction

Fault: It is possible that the connection between the B+ cable and the Power Distribution Box can become damaged by wear and heat which is caused by high current flow and high contact resistance. Normally this will result in a non-start situation after parking the vehicle. However it is possible that this could in extreme cases occur whilst the vehicle is in motion. The driver should be made aware of the issue by flickering of the instrument cluster (dash) or an engine mis-fire; but if the driver does not then the engine could cut-out without warning.

Fix: Recall all affected vehicles with petrol engines and replace the cable/connection with a more robust item.

Recall R/2017/114 · Dated 10 April 2017 · Built 1 December 2009 to 13 October 2011

36,410
Dec 2016
Power steering may not perform correctly

Fault: The electrical contact of the Electronic Control Unit (ECU) of the Electric Power Steering (EPS) is not sufficiently robust over the service life of the vehicle. As a result the power steering support may fail possibly leading to disconcerting driving situation for the driver. Additionally in a few cases a localised thermal event cannot be excluded.

Fix: Recall the vehicles that are likely to be affected and replace the steering gear (EPS).

Recall R/2016/300 · Dated 21 December 2016 · Built 19 September 2011 to 8 December 2015

41
Nov 2016
Drivers airbag may deploy incorrectly

Fault: The driver's air bag inflator may rupture during deployment. Metal shards may pass through the air bag material and cause injury to occupants.

Fix: On affected vehicles replace air bag and inflator assemblies.

Recall R/2016/252 · Dated 1 November 2016 · Built 1 March 2002 to 31 December 2003

218,559
Oct 2016
Possible loss of control

Fault: The bolts securing the rear axle support should not be re-used after removal. Affected vehicles may have had the rear axle support refitted after repair work using the original fitted bolts. These may work and though noise and vibration are likely continued use may affect the vehicle's handling.

Fix: On affected vehicles replace the rear axle support bolts.

Recall R/2016/224 · Dated 4 October 2016 · Built 1 January 2015 to 1 September 2016

60
Jun 2015
Engine may stall

Fault: The in tank fuel pump may contain sub components that have not been correctly nickel plated. This may cause excessive friction leading to the fuel pump being inoperative. The driver may experience a no start condition or in the worst case an engine stall. A warning lamp and error message will display. Steering and brakes will still function.

Fix: Recall the vehicles that are likely to be affected and replace the in tank fuel pump with a modified version.

Recall R/2015/109 · Dated 8 June 2015 · Built 1 September 2013 to 30 April 2014

1,646
Jan 2015
Seat belt may malfunction

Fault: On affected vehicles the Driver's seatbelt retractor may be faulty. The seat belt may be hard to pull out or below zero degrees it may not be possible to pull the belt out. In these instances a driver may not be able to use the belt as intended.

Fix: On affected vehicles Check belt operation and replace belt if necessary

Recall R/2014/188 · Dated 6 January 2015 · Built 1 September 2014 to 31 March 2015

1,502
Jul 2014
Engine emergency mode may be activated during driving

Fault: The screws retaining the variable camshaft timing (VANOS) housing may loosen and under certain circumstances the heads may break off. This can lead to the VANOS leaking oil internally and adversely affect the valve timing adjustment. If found to deviating from targeted data the engine emergency mode will be activated. This will be indicated by a distinct change in engine running. The orange engine management warning lamp and a check message; On vehicles with N51/N52 engines this will appear at ignition recycle on N55 engine it will display immediately.

Fix: Repalce bolted connection of the VANOS adjustment unit

Recall R/2014/068 · Dated 28 July 2014 · Built 1 September 2009 to 30 November 2011

2,967
Jul 2013
Passenger side airbag may fail to deploy correctly

Fault: The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

Recall R/2013/071 · Dated 26 July 2013 · Built 1 May 1999 to 31 August 2006

316,043
Jul 2013
Loss of drive

Fault: It is possible that over a period of time the bolt securing the clutch cover/pressure plate may become loose. The drive should be warned of this by the behaviour of the clutch noise from it or inability to select gears. Under certain conditions complete loss of drive could occur which could place the driver and occupant of the vehicle in a prone position.

Fix: Recall all affected vehicles and replace the clutch bolts.

Recall R/2013/080 · Dated 5 July 2013 · Built 1 February 2013 to 30 June 2013

4
Apr 2013
Engine may cut out

Fault: It is possible that the connection between the B+ cable and the Power Distribution Box can become damaged by wear and heat which is caused by high current flow and high contact resistance. Normally this will result in a non-start situation after parking the vehicle. However it is possible that this could in extreme cases occur whilst the vehicle is in motion. The driver should be make aware of the issue by flickering of the instrument cluster (dash) or an engine mis-fire; but if the driver does not then the engine could cut-out without warning.

Fix: Recall all affected vehicles and replace the cable/connection with a more robust item.

Recall R/2013/024 · Dated 4 April 2013

36
Dec 2012
Rear window may detach

Fault: It is possible side and rear windows made out of Makrolon (Synthetic Polycarbon Laminate) may become loose due to insufficient adhesion fixing them in place. This will result in a visual and audible warning of the issue to vehicle occupants. If these warnings are ignored it is possible a window could detach from the vehicle.

Fix: Recall affected vehicles and replace the Makrolon windows with conventional glass windows.

Recall R/2012/149 · Dated 11 December 2012

17
Jul 2012
Eps may not perform as specified

Fault: Due to a component in the integrated control module not being to specification it is possible power steering assistance may fail. If this happens the EPS warning lamp will illuminate and a check control message will appear on the dashboard display. Directional control will be maintained albeit with additional driver input.

Fix: Recall vehicles likely to be affected to replace the steering box.

Recall R/2012/081 · Dated 30 July 2012 · Built 1 February 2007 to 31 December 2011

1,402
Jun 2009
Front side airbag or SEAT belt tensioner may not operate correctly

Fault: It has been identified that due to faulty crimping of the component parts of the airbag wiring harness and seat belt tensioner the side airbag or seatbelt tensioner may not trigger in the vent of a collision.

Fix: Recalled vehicles will have the harness checked and repaired as necessary.

Recall R/2009/065 · Dated 30 June 2009 · Built 23 May 2008 to 21 July 2008

1,756
Feb 2008
Door pressure sensors may delay side airbag deployment following an impact.

Fault: It has been identified that the connections for the left and right hand door pressure sensors have been reversed at their connection with the airbag control unit. This would have the effect of delaying the detection of a side impact thus causing the airbag to be deployed too late. It should be noted that the fault would not be indicted by the illumination of the airbag system warning lamp.

Fix: Recalled vehicles will have the pin assignment of the airbag control unit corrected.

Recall R/2008/026 · Dated 14 February 2008 · Built 20 November 2006 to 11 January 2008

7,703
Dec 2006
Steering lock may inadvertently engage

Fault: The control cam of the steering lock may break. This is most likely to occur as the vehicle is started or parked. However the possibility of this occurring whilst the vehicle is in motion cannot be ruled out. In this event the steering lock could engage with the effect that it would no longer be possible to steer the vehicle.

Fix: Recall affected vehicles check manufacturer of lock and if necessary replace steering lock.

Recall R/2006/199 · Dated 22 December 2006 · Built 1 November 1995 to 1 November 1996

2,222
Nov 2006
Possible loss of braking power assistance

Fault: A temporary fault in the greasing system on the brake servo sealing ring could lead to the sealing ring being subject to wear. In unfavourable conditions the seal may be pressed into the brake servo housing as a consequence of increased friction. The arising leak will cause a hissing sound audible within the vehicle interior with the additional consequence that there may be a risk that loss of brake assistance will ensue.

Fix: Recalled vehicles will have the brake servo replaced.

Recall R/2006/207 · Dated 28 November 2006 · Built 4 March 2006 to 14 March 2006

287
Feb 2005
The bearings of the fuel injection pump may fail

Fault: The bearings of the high pressure fuel injector pump may fail after a short travelled distance (approximately 3000 to 6000 miles) This leads to a total failure of the engine's fuel supply which results in the engine stalling.

Fix: Recall likely to be affected vehicles and replace the fuel injector pump.

Recall R/2005/022 · Dated 8 February 2005 · Built 30 November 2004 to 31 January 2005

697
Feb 2002
Possible detachment of ball bearing from front suspension strut top mounting

Fault: It is possible that the ball bearing in the front suspension strut top mounting may not have been securely fitted. If the weight of the car is taken off of the road wheel for any reason the bearing may became displaced with a risk of personal injury or damage to the suspension.

Fix: Replace both front suspension strut mounts.

Recall R/2002/025 · Dated 22 February 2002 · Built 6 November 2001 to 20 November 2001

2,023
Nov 2001
Tyres may have cuts in side walls.

Fault: Cuts have been observed on isolated Continental tyres fitted to vehicles. The cuts (1-5 cm in length) are of varying severity and can lead to a loss of tyre pressure. This can destroy the tyre if the vehicle continues to be driven.

Fix: Recall affected vehicles examine all tyres and replace any found with cuts in the sidewalls.

Recall R/2001/146 · Dated 9 November 2001 · Built 28 September 2001 to 24 October 2001

264
Feb 2001
Lower steering shaft may fail

Fault: Due to the long term effects of corrosion the above vehicles are being recalled. The corrosion is an age related problem and this recall action will target the oldest cars first in groups of 15000 to 20000. It is believed that as long as the vehicle has a current MOT and is serviced correctly any possible corrosion problems with the shaft will be highlighted as a matter of course. If customers are concerned they can visit any BMW dealer to have the shaft checked.

Fix: DEFECT (cont.) If the component is safe the car will not be repaired at this stage but will be recalled at a later date as originally planned. REMEDY Recall affected vehicles and fit modified lower steering shaft.

Recall R/2000/135 · Dated 26 February 2001 · Built 1 January 1991 to 31 December 1998

285,722
Dec 1999
Brake lights may fail to operate remain on or flicker

Fault: There is a possibility that the brake light switch circuits may become defective and cause the brake light circuit to fail stay on continuously or flicker. In extreme cases the brake switch could overheat.

Fix: Recall affected vehicles and replace brake light switch with a modified version.

Recall R/1999/104 · Dated 15 December 1999 · Built 16 September 1999 to 28 October 1999

5,634
May 1999
Possible unscheduled deployment of side airbags and activation of battery isolator switch

Fault: In certain driving conditions it is possible for the side airbags and the battery terminal (safety isolation switch) to trigger when this is not necessary ie when no accident has occurred.

Fix: Recall the affected vehicles and recode the airbag control unit.

Recall R/1999/047 · Dated 25 May 1999 · Built 1 September 1998 to 14 April 1999

16,646
May 1997
Corrosion on lower steering shaft

Fault: Instances of corrosion on the corrugated section of the lower steering shaft have occurred. This could lead to eventual weakening of the shaft.

Fix: All vehicles fitted with corrugated type lower steering shafts will have them replaced with quality assured examples.

Recall R/1997/005 · Dated 27 May 1997 · Built 1 February 1991 to 31 December 1994

80,000
Feb 1996
Security of stub axle mountings

Fault: The three bolts which secure the stub axle to the spring strut may not have been fully torqued on initial assembly.

Fix: Recall the affected vehicles and check the torque setting on the bolts involved retorqueing as required. Any bolts found to have been loose (as distinct from being insufficiently torqued) will be replaced.

Recall R/1996/037 · Dated 23 February 1996 · Built 8 January 1996 to 30 January 1996

1,600
Apr 1995
Possible damage to wheel bearings

Fault: Due to production tolerances at the halfshaft splines the rear wheel bearings may not have been correctly pre-loaded during assembly. This could lead to bearing damage and premature failure.

Fix: Recall the affected vehicles and check the halfshaft flange connection. Where this is outside prescribed tolerances the halfshaft and roller bearing will be replaced.

Recall R/1995/030 · Dated 7 April 1995 · Built 7 February 1995 to 20 March 1995

152
Feb 1992
Possible chafing of the battery cable

Fault: Chafing may occur where two cables pass through a grommet in the front bulkhead. This could result in a short circuit and fire risk.

Fix: Recall affected vehicles. De-energise the 6 sq.mm. battery positive cable which backs up the engine management system by cutting it at both ends and taping it to the cable. An alternative arrangement is being made to back up the engine management system.

Recall R/1992/013 · Dated 28 February 1992 · Built 1 January 1991 to 28 February 1992

8,700

Nothing matches that search on this page.

Vehicles affected is the number DVSA lists for each recall.

How to check a car for recalls

A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.

A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.

Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.

Frequently asked questions

How do I check if my 3 Series has an outstanding recall?

Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.

How many recalls has the BMW 3 Series had?

DVSA's recalls data lists 66 safety recalls covering the BMW 3 Series, the most recent dated 2 March 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.

Does a recall mean a car is unreliable?

No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.

What should I do if my car is affected by a recall?

Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.

Where does this recall data come from?

From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.

Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.

Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.

Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.

Free vehicle check on WhatsApp

Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.

Open WhatsApp

How it works

Looking for a BMW 3 Series?

See used BMW 3 Series cars listed on the MotifyMe® marketplace.

See 3 Series cars for sale