BMW 5 Series Recalls
Safety recalls covering the BMW 5 Series in DVSA's recalls data, newest first.
Last updated 22 November 2026
Short answer:
DVSA's recalls data lists 66 safety recalls covering the BMW 5 Series, the most recent dated 9 November 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Check a registration for outstanding recalls, free
Every BMW 5 Series recall
Open a recall to see the fault, the fix and the build dates it covers.
| Date | Recall | Vehicles affected |
|---|---|---|
| Nov 2026 | Check/replace starter motor gxx PHEVFault: The fault relates to the SEG engine starter that was designed as a replacement part for vehicles affected by the VALEO engine starter recall (BMW 0012840600). It was found that for a specific production batch the wrong relay was installed due to a process error. There is a chance that the preload in the bolted joint securing the B+ lead to the starter may be lost for example due to corrosion or temperature fluctuations and that the joint may consequently come loose. If the screw connection on the B+ cable comes loose sparks may be created in the vicinity of the screw connection (only whilst the vehicle or the starter is in operation). It cannot be excluded that a thermal incident might occurs resulting from the ignition of a flammable load caused by sparks in the vicinity of the screw connection. In this case smoke is noticeable while driving or when exiting the vehicle. Fix: On the affected vehicles the starter motor will be checked and if necessary replaced again. | 6 |
| Mar 2026 | Checking and re-securing the air-conditioning wiring harnessFault: The Safety Recall relates to the air-conditioning wiring harness located behind the dashboard. On the affected vehicles the wiring harness was fixed very close to a screw connection on the interior microfilter housing cover. The microfilter of the air conditioning system will be regularly replaced as part of the oil service. It cannot be ruled out that cables may be damaged when replacing the microfilter during a workshop visit. The filter cover has to be removed from the lower part of the instrument panel. After replacing the filter the cover has to be refitted at which point the wires may become damaged or trapped. If the wiring harness is damaged this could lead to malfunctions of the air conditioning system as well as to a short circuit. In case of a short circuit a sensor may overheat while the vehicle is in operation. As a result smoke may develop from the instrument panel and subsequently a fire cannot be ruled out. Fix: On the affected vehicles the air-conditioning wiring harness will be checked repaired if necessary and re-secured in a modified fixing. | 8,651 |
| Mar 2026 | Replace the engine starter motorFault: The Safety Recall relates to the engine starter motor. The fault relates to the RSW22 starter RWT (reinforced water tightness). It was found that with RWT starters an increased abrasion of the magnetic contact can cause the growth of deposits at the lowest point of the relay interior. This in turn may increase the relay contact resistance resulting in false starts or even causing short circuits and possibly a thermal reaction. In case of a short circuit the possibility of a thermal event cannot be excluded. This may happen while attempting to start the vehicle or while driving due to vibrations causing a short circuit due to moving deposits. Fix: On the affected vehicles the starter motor will be replaced with a variant by another supplier with a different design. Until the repair has been completed it is recommended to not leave the vehicle running unattended after starting the engine. | 9 |
| Dec 2025 | Takata driver and/or passenger airbag recall (global vins)Fault: Affected vehicles are already included in Safety Recalls within the markets they have previously resided in. The vehicles may be fitted with a driver and/or passenger airbag/s which if deployed may do so with excessive force causing sharp metal fragments to be released this may cause serious injury which could prove fatal to people in the vicinity. Fix: Vehicles will have the affected airbags checked and if necessary replaced. | 9,471 |
| Nov 2025 | Program control units (coc documents)Fault: A quality check has revealed that the affected G61 vehicles software does not reflect the associated CoC documentation. Fix: To ensure your vehicle is in perfect working order we would like to program the control units to adapt the vehicle's software level to the CoC documents. as soon as possible. Naturally this work will be free of charge. | 263 |
| Oct 2025 | Replace the engine starter motorFault: For affected vehicles there is a concern involving water ingress and corrosion to the starter motor for where a short circuit cannot be ruled out. It is strongly recommended to park the vehicle outdoors and not in the immediate vicinity of buildings until the repair has been carried out. Fix: Replacement of the starter motor. | 43,163 |
| Oct 2024 | Hydraulic brake system unit replacementFault: On affected vehicles the brake servomotor was improperly welded. The weld seam might not withstand the stresses caused under high brake pressure leading to a requirement for a higher brake effort increasing the braking distance. Fix: Affected vehicles will have the hydraulic unit of the brake system replaced. | 11 |
| Oct 2024 | Check driver’s airbag for conversion takata sdi & psdi-5Fault: Affected vehicles may have had a retrofit or conversion of the airbag using a previously recalled airbag variant which if deployed may do so with excessive force causing sharp metal fragments to be released this may cause serious injury possibly fatal to people in the vicinity. The original factory fitment airbag for the vehicle is not affected. Fix: Vehicles will have the airbag checked and if necessary replaced. | 85,920 |
| Oct 2024 | Replace double universal joint (steering)Fault: On affected vehicles there may have been a deviation in the production of the double universal joint on the steering column. Certain steering movements could result in the component failing. Fix: Affected vehicles will have the double universal joint replaced. | 828 |
| Sep 2024 | Integrated braking systemFault: On certain vehicles the Integrated Brake (IB) system may be impaired due to contamination between electrical contacts. Fix: Vehicles that may be affected by contamination are required to have the vehicle's software updated which can detect signal interference before it occurs. If symptoms are detected you should refrain from use of the vehicle and the affected Integrated Brake (IB) system component will be replaced. | 6,597 |
| May 2024 | Replace vanos bolts n51 n52 n55Fault: On affected vehicles overtime the aluminium screws can loosen or break on the adjustable variable camshaft timing (VANOS) units potentially resulting in engine emergency mode being activated. Fix: On affected vehicles the eight aluminium screws will be replaced if evidence of faulty screws is found then the VANOS adjustment unit will also be replaced. | 11 |
| Mar 2024 | Integrated braking systemFault: On affected vehicles an unexpected loss of hydraulic brake assistance may occur and may result in a different pedal behaviour under specific conditions an extended braking distance may be experienced and ABS/Stability control may be impaired Fix: On the affected vehicles the Integrated Brake System will be replaced | 12 |
| Feb 2024 | Isofix fixing g60Fault: On affected vehicles the rear seat ISOFIX bracket may have been damaged during the production process and may allow the seat to detach in the event of an accident Fix: On affected vehicles the ISOFIX fixing will be inspected and if necessary replaced | 113 |
| Nov 2023 | Check steering wheel and rework ground connectionFault: On affected vehicles the steering wheel ground connection may have been insufficiently fastened during production which may result in the system detecting the hands are on the steering wheel even though they are not�� Fix: On affected vehicles the steering wheel ground connection will be checked and if required reworked.� | 1,208 |
| Jan 2023 | A possible degradation of the propellant tablets could lead to an over-aggressive combustion in the event the airbag is activated which may cause the inflator body to rupture.Fault: A possible degradation of airbag propellant tablets could lead to an over-aggressive combustion in the event the airbag is activated which may cause the inflator body to rupture. Fix: On affected vehicles the drivers airbag module will be replaced. | 39,648 |
| Sep 2022 | In rare cases the starter motor can inadvertently be activated permanently presenting a risk of a thermal eventFault: In rare cases the starter motor can inadvertently be activated permanently presenting a risk of a thermal event. Fix: Rework the starter motor assembly. | 25,982 |
| Aug 2022 | Screw connections of some seats and seatbelts may not have been properly tightened during vehicle productionFault: Screw connections of some seats and seatbelts may not have been properly tightened during vehicle production. Fix: : Inspect and ensure all affected seats and belts are correctly secured and tightened to specification. | 6 |
| Aug 2022 | Undetected EGR system leaks may cause thermal activity in the intake manifoldFault: Undetected EGR System leaks may cause thermal activity in the intake manifold. Fix: The engine management control unit (DDE) will be programmed with improved software incorporating the latest OBD functionality. | 1,290,980 |
| Aug 2022 | The exhaust gas recirculation cooler may leak over time and cause thermal incidentFault: The Exhaust Gas Recirculation cooler may leak over time and cause thermal incident. Fix: On the affected vehicles the EGR cooler module will be replaced. | 1,596,995 |
| Mar 2022 | The obd software could misinterpret certain input parameters for the engine mangement systemFault: During a service visit the affected vehicles have been updated with software that could misinterpret certain input parameters for the engine management system. Fix: The control units will be reprogrammed with an improved version of software. | 12,802 |
| Dec 2021 | The material quality of the screws used for SEAT belts and rear seats may not be to specifications.Fault: The material quality of seat and seatbelt screws may not be according to specification. Fix: On the affected vehicles the screws will be replaced in specific locations on the seat belts or rear seats. | 38 |
| Oct 2021 | Thermal ageing of inline fuse located on the front right spring strut domeFault: Thermal ageing of an inline fuse located on the front right spring strut dome. Fix: Modify the circuit to a later specification and replace the fuse. | 8,875 |
| Jun 2021 | A microprocessor fault in the airbag control unit can lead to faulty operating conditionsFault: A microprocessor fault in the airbag control unit can lead to faulty operating conditions. Fix: The airbag control unit will be replaced. | 354 |
| Mar 2021 | The rear drive shafts may not fulfil the durability requirementsFault: The rear drive shafts may not fulfil the durability requirements. Fix: On the affected vehicles one or both output shafts will be replaced. | 30 |
| Mar 2021 | Affected vehicles may be fitted with brake discs which are not to specificationFault: Affected vehicles may be fitted with brake discs which were not produced according to the specifications Fix: On the affected vehicles the brake discs will be checked and if necessary replaced | 1,410 |
| Feb 2021 | The exhaust gas recirculation cooler could leak over timeFault: Leaking glycol coolant could create in combination with soot and oil sediments in the EGR module ignitable deposits. Fix: The EGR cooler will be internally inspected with an endoscope and replaced if evidence of leaking is found. | 255,552 |
| Jan 2021 | The battery cables on the 48v starter generator may not have been sufficiently secured during productionFault: The battery cables on the 48V starter generator may not have been sufficiently secured during the production process. Fix: Check the screw connection of the 48V positive / negative battery cables on the starter generator and rework if necessary. | 776 |
| Dec 2020 | Remaining particles in the cells of the high voltage battery can cause a short circuitFault: A possibility of impurities contained in the HV batteries may cause short circuit. Fix: Testing of battery charge cycles and replacement of the HV cells where necessary. | 5,330 |
| Oct 2020 | Remaining particles in the cells of the high voltage battery can cause a short circuitFault: In very rare cases welding beads were not always completely removed in the cleaning process during battery production. Fix: Test and replace the High Voltage batteries if affected. | 871 |
| May 2020 | If the head air bag is deployed the ignitor may separate from the inflatorFault: Curtain airbags may have propellant which may have a humidity level higher than specification and in the event of a collision may not deploy correctly increasing the risk of injury. Fix: Replace the airbags on affected vehicles. | 322 |
| Dec 2019 | The pressing force of the bearing bushing into the crankcase may be out of specificationFault: The engine counterbalance shaft bearing bushing into the crankcase may be out of specification Fix: Replace the engine of affected vehicles | 106 |
| Jul 2019 | Possible corrosion of the bulkhead connector of the positive battery cableFault: The branch-off point of the main battery cable may corrode Fix: The branch-off point will be checked and reworked appropriately depending on the level of corrosion present | 121,849 |
| Mar 2019 | Potential rupture of driver front air bag inflatorFault: The front drivers air bag may not deploy correctly on activation. Fix: Check and replace the drivers front air bag if required. | 24,980 |
| Mar 2019 | Auxiliary water pump's electronic circuit board could lead to a short circuitFault: The auxiliary water pump may short circuit causing a thermal incident. Fix: The Auxiliary Water Pump of the affected vehicles will be replaced. | 17,598 |
| Dec 2018 | Exhaust gas recirculation module cooler could leakFault: The EGR cooler may leakpresenting a fire risk Fix: A visual inspection of the EGR cooler to check for leaks and excessive build-up of deposits. The EGR cooler will be replaced on all affected vehicles | 676,347 |
| Nov 2018 | Exhaust gas recirculation cooler could potentially leak over timeFault: The EGR cooler may leakpresenting a fire risk. Fix: The EGR cooler will be replaced with an improved version. | 614,408 |
| Oct 2018 | Software fault in crankshaft sensorFault: The affected vehicles may be equipped with a crankshaft sensor with a software fault. Fix: On the affected vehicles the crankshaft sensor will be replaced with a new version. | 1,642 |
| Aug 2018 | Software fault with crankshaft sensorFault: The affected vehicles may be equipped with a crankshaft sensor with a software fault. The crankshaft sensor cannot process the signal values from the crankshaft transmitter due to an improper firmware level. The firmware does not compensate sufficiently the temperature gradients and the magnetic field strength of the sensor electronic. If the crankshaft sensor cannot process the signal values from the transmitter the Digital Diesel Electronic (DDE) will notice that and change to the emergency operation mode. The emergency mode will be displayed by the check control message �engine malfunction�. The driver may notice a rough running engine and a reduced driving power (70%). However an engine stalling during driving conditions cannot be excluded. Fix: On the affected vehicles the crankshaft sensor will be replaced with a new version. | 8,050 |
| Sep 2017 | Steering rack might lockFault: If the retaining ring inside the steering gear has not been fitted correctly the sealing cap would not be fixed axially and might start moving. If the sealing cap has moved the ball return channel would not be fixed anymore and might move out of position possibly resulting in a ball jam accompanied by an extensively increased steering force and possibly lock. Fix: Recall the vehicles that are likely to be affected to fit a new steering rack and ensure it is programmed correctly. | 3 |
| Jun 2017 | Brake switch may be activated permanentlyFault: The ball head connecting the brake pedal and the master brake cylinder the ball head might not be locked properly into the ball cage. If the driver accidentally pulls up the brake pedal the brake switch would be activated permanently. This will cause: The brake lamps to be illuminated even while driving A Check Control Message would not alert the driver. An engine start or gear selection would be possible without brake actuation. If the driver's door were opened after switching off the engine the gear would not switch automatically to P as designed. Fix: Recall the vehicles that are likely to be affected and check the locking of the ball head on the brake pedal. If necessary the pedal mechanism will be replaced. | 24 |
| Apr 2017 | Driveshaft universal joint may breakFault: Due to insufficient strength the front universal joint in the rear front universal joint of the rear prop shaft may fail. Fix: On affected vehicle replace the universal joint with a modified version | 10,849 |
| Jan 2017 | Airbags may not deployFault: The igniter for the certain airbag modules may not have been correctly manufactured which may affect air bag deployment in the event of a collision. Fix: Where necessary replace affected airbag modules. | 668 |
| Nov 2016 | Front airbags and SEAT belt tensioners may fail to deploy when neededFault: It has been identified that the airbag/SRS central sensor has been programmed with faulty software. If the vehicle is involved in a frontal or rearward collision then the airbag and seat belt tensioners may not be triggered which could lead to an increased risk of injury to the occupants. Fix: Recall all affected vehicles for the replacement of the airbag/SRS central sensor. | 1,047 |
| Nov 2016 | Drivers airbag may deploy incorrectlyFault: The driver's air bag inflator may rupture during deployment. Metal shards may pass through the air bag material and cause injury to occupants. Fix: On affected vehicles replace air bag and inflator assemblies. | 218,559 |
| Jul 2014 | Engine emergency mode may be activated during drivingFault: The screws retaining the variable camshaft timing (VANOS) housing may loosen and under certain circumstances the heads may break off. This can lead to the VANOS leaking oil internally and adversely affect the valve timing adjustment. If found to deviating from targeted data the engine emergency mode will be activated. This will be indicated by a distinct change in engine running. The orange engine management warning lamp and a check message; On vehicles with N51/N52 engines this will appear at ignition recycle on N55 engine it will display immediately. Fix: Repalce bolted connection of the VANOS adjustment unit | 2,967 |
| Dec 2013 | Towing ball hitch may detachFault: Electronically deployed tow hitch is automatically deployed by button located ion luggage compartment. The pivot uses a mechanical control link which is electrically adjusted. This is necessary to prevent a loosening or shaking loose of the end stop during driving. Due to a software error in the instrument cluster the driver may not in certain cases get prior warning if the adjustment fails. The consequences of this are that the ball hitch can shake loose from the end stop whilst driving. The control link can break due to the imposed load of the trailer and the hitch can pivot downwards causing loosening/detachment of the trailer and adversely affect the vehicle control. Fix: Recall affected vehicles and reprogramme the control unit/instrument cluster. | 13 |
| Sep 2013 | Possibility of fireFault: Due to a fault with an internal connection within the Fuel Filter Heater (FFH) it is possible that during temperatures below freezing the FFH can remain permanently activated. This will normally cause the FFH to overheat which will result in the inability to start the vehicle due to a flat battery. This can occur even when the ignition is turned off. However in extreme cases it could cause a vehicle fire. Fix: Recall all affected vehicles to replace the FFH. | 21,502 |
| Sep 2012 | Engine may failFault: In individual cases the oil pump may no longer provide the required oil pressure. This may cause severe engine damage. Additionally the occurrence of critical driving situations cannot be ruled out because the oil pressure may drop suddenly while driving. The driver will usually notice a drop in the engine oil pressure due to the check control message ''Low oil Pressure''. It is also possible the engine block will be damaged and as a result engine oil may be lost. Fix: The oil pump will be replaced with the correct version. | 80 |
| May 2012 | Risk of fireFault: The positive battery cable routed from the vehicle battery to the engine bay consists of one cable in the luggage compartment and one cable in the underbody. Both cable are connected by a screw connection and covered by a plastic cover. In single cases the plastic cover may have been fitted incorrectly during the vehicle production. Over time an incorrectly fitted cover could cause the screw connections to come loose leading to an increased resistance also humidity may affect the connection and cause high resistance and drop in current. This can lead to the vehicle not starting and in extreme cases the connection could over heat leading to the possibility of a fire in the luggage area. Fix: The clips on the battery will be checked the cover replaced and sealed. | 257,402 |
| Apr 2012 | Fire may occurFault: Some engines are fitted with an additional water pump for the turbo charger. In some circumstances a crack may develop which then leads to melting of the plug connections and the housing. Further heat development may then lead to scorch damage. In exceptional cases such overheating can lead to smouldering of the water pump. If smouldering occurs an engine compartment fire and vehicle fire cannot be excluded. Fix: The water pump will be replaced for a new more robust version. | 21 |
| Nov 2011 | Short circuit may occurFault: Due to the ingress of moisture it is possible that a short circuit can occur in the additional coolant pump for the exhaust turbocharger. The driver will be informed of the issue by a warning message on the display in the instrument panel. If not addressed it is possible for further heat build up in the pump which may cause the plug connection and housing to melt and in extreme cases a localised fire in the engine compartment or vehicle. Fix: Recall all affected vehicles for the replacement of the additional coolant pump. | 557 |
| Oct 2011 | Risk of fireFault: Moisture may enter the fuel filter heater at an electrical connection. Should this occur it can cause a discharge of the battery causing non starting of the vehicle. Also if it occurs whilst the vehicle is in motion it could result in a fire when the vehicle is left unattended. Fix: Recall all affected vehicles and replace the fuel filter heater. | 21,923 |
| Nov 2010 | Possible reduction in brake servo assistanceFault: It is possible that engine oil can enter the brake servo via the brake vacuum pump and vacuum hose. If this occurs it could damage the brake servo membrane which may leak so causing a reduction in braking assistance and a requirement to apply increased pedal force to achieve the same braking efficiency. Fix: Recall all affected vehicles for the fitment of a modified servo hose. In addition the checking of the brake servo for contamination and replacement if required. | 10,567 |
| Jul 2008 | Rear axle carrier may failFault: It has been identified that defects in a material joint may have resulted during the heat treatment of individual components of the rear axle carrier. This may result in failure of the holders of the links and struts even under normal driving conditions. Should the holder of a link fail whilst the vehicle is in motion the handling characteristics of the vehicle would undergo an unexpected change which could result in an accident. Fix: Recalled vehicles will be checked and if necessary fitted with a quality assured rear axle carrier. | 1,330 |
| Jul 2006 | Rear shock absorber mounting may failFault: It has been identified that the lower rubber mounting on the metal bush of the rear shock absorbers may fail to meet the quality requirement. Dependant on the mileage and operating conditions the rubber mounting may come completely free from the shock absorber. If this occurs the bodywork would no longer be supported above the wheels causing it to come into contact with the wheel concerned. Should this occur the possibility exists that a critical driving condition might occur or even the risk of an accident. Fix: Recalled vehicles will have the rear shock absorbers checked and replaced if necessary. | 3,743 |
| Feb 2005 | The bearings of the fuel injection pump may failFault: The bearings of the high pressure fuel injector pump may fail after a short travelled distance (approximately 3000 to 6000 miles) This leads to a total failure of the engine's fuel supply which results in the engine stalling. Fix: Recall likely to be affected vehicles and replace the fuel injector pump. | 697 |
| Dec 2004 | Front SEAT back-rest heater may overheatFault: Mechanical loads exerted on the back-rest heating element of the front seats when persons enter or exit the vehicle may result in damage to the door side contact line in the back-rest padding. In the event that this causes a break of a contact line the damaged area may overheat to unacceptable levels with the heater switched on. It would then not be possible to rule out the risk of minor burns to the occupants clothes and possibly their skin. Fix: Recall affected vehicles and check condition where necessary fit an additional in-line fuse. | 3,009 |
| Jul 2004 | Possibility of inadvertnent loss of engine powerFault: Due to a hardware fault within the digital engine electronic control unit the possibility exists that the unit could fail completely resulting in loss of engine power. Fix: Recall likely to be affected vehicles and replace the control unit with a quality assured item. | 231 |
| May 2004 | Possibility of inability to engage gear or declutchFault: Possibility that the pin operating the master cylinder may have been welded incorrectly. Resulting in the inability (on failure) to de-clutch or engage a gear. Fix: Recall likely to be affected vehicles inspect the subject weld and replace the clutch pedal if the weld is found to be faulty. | 2,652 |
| Mar 2004 | Possibile fault in the dsc yaw rate sensorFault: Due to a possible manufacturing error the damping element of the Directional Stability Control (DSC) yaw rate sensor could be faulty. Fix: Recall the affected vehicles check the batch number and replace if necessary. | 45 |
| Nov 2003 | Unintentional deployment of airbagFault: A possible fault in the microprocessor in the air bag control unit could lead to an uncontrolled setting of the output signals from the control unit immediately after switching on the ignition. In unfavourable conditions this may lead to components of the safety and restraint system being triggered. This fault does not affect the vehicle while the car is being driven. Fix: Recall affected vehicles and replace and code the air bag control unit. | 8,176 |
| Feb 2002 | Possible detachment of ball bearing from front suspension strut top mountingFault: It is possible that the ball bearing in the front suspension strut top mounting may not have been securely fitted. If the weight of the car is taken off of the road wheel for any reason the bearing may became displaced with a risk of personal injury or damage to the suspension. Fix: Replace both front suspension strut mounts. | 2,023 |
| Jan 2002 | Engine cooling fan may fail.Fault: Manufacturing faults and software errors in the electronics of the electric fan could cause these components to be thermally overloaded and destroyed. In isolated cases the overloading could lead to scorching or a fire in the fan. Fix: Recall affected vehicles and check the fan type and build. Replace the fan where necessary. | 7,500 |
| Nov 2001 | Tyres may have cuts in side walls.Fault: Cuts have been observed on isolated Continental tyres fitted to vehicles. The cuts (1-5 cm in length) are of varying severity and can lead to a loss of tyre pressure. This can destroy the tyre if the vehicle continues to be driven. Fix: Recall affected vehicles examine all tyres and replace any found with cuts in the sidewalls. | 264 |
| Dec 1999 | Brake lights may fail to operate remain on or flickerFault: There is a possibility that the brake light switch circuits may become defective and cause the brake light circuit to fail stay on continuously or flicker. In extreme cases the brake switch could overheat. Fix: Recall affected vehicles and replace brake light switch with a modified version. | 5,634 |
| Jul 1999 | Possibility that gearbox may lock upFault: Possibility that the automatic transmission may lock up at speeds below 15mph. Fix: Recall affected vehicles and fit a new quality assured gearbox. | 12 |
Nothing matches that search on this page.
Vehicles affected is the number DVSA lists for each recall.
How to check a car for recalls
A recall only applies to vehicles built within set dates or VIN ranges, so a recall listed for a model does not mean every car of that model is affected. To check a particular car, enter its registration in our free reg lookup, which shows whether DVSA records an outstanding recall. You can then confirm on GOV.UK's check vehicle recalls service.
A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
Buying used? A free check does not cover outstanding finance, write-off or stolen records. For those, use our vehicle history check, with data provided by Experian.
Frequently asked questions
How do I check if my 5 Series has an outstanding recall?
Enter the registration in the free MotifyMe reg lookup. It shows whether DVSA records an outstanding recall for that vehicle. You can then confirm the details on GOV.UK's check vehicle recalls service.
How many recalls has the BMW 5 Series had?
DVSA's recalls data lists 66 safety recalls covering the BMW 5 Series, the most recent dated 9 November 2026. A recall only applies to vehicles built within set dates or VIN ranges, so check the registration with our free reg lookup to see whether a car has an outstanding recall, then confirm on GOV.UK.
Does a recall mean a car is unreliable?
No. A recall count is not a reliability score. Recalls are how manufacturers put faults right, and models sold in large numbers over many years tend to appear more often.
What should I do if my car is affected by a recall?
Contact a dealer for that make or the manufacturer and quote the recall number. Each recall listing explains the fault and the fix the manufacturer has set out.
Where does this recall data come from?
From DVSA's vehicle recalls data, published under the Open Government Licence v3.0. MotifyMe refreshes these pages from the latest DVSA file each month. These pages were last updated on 22 November 2026.
Recalls are matched to models by the model names in DVSA's file, so a recall listed under a different name may not appear here. Always check the individual vehicle.
Contains public sector information licensed under the Open Government Licence v3.0. Source: DVSA vehicle recalls data.
Last updated 22 November 2026. These pages are refreshed from the latest DVSA file each month.
Send a UK registration to +44 7537 185888 and we reply in the chat with a free vehicle check.
What it can do
- ✓Free vehicle check: send any UK reg for the make, model, MOT and tax status
- ✓Send a photo of a number plate and we read the reg for you, then ask you to confirm it
- ✓Outstanding safety recall check, included in every lookup
- ✓Free valuation: add the mileage after the reg, for example 45k. A guide only, not an offer to buy or a guarantee of sale price See terms
- ✓Free MOT and tax reminders: reply REMIND with a reg (typos are fine)
- ✓Paid vehicle history check, with data provided by Experian, delivered in the chat
- ✓Find a vehicle: for example Ford Fiesta under 8k
- ✓Ask about a vehicle: send your question with the link to the vehicle on MotifyMe or its registration. Or search first, then reply ASK, the number of the vehicle and your question, for example ASK 2 is it still available. If we are not sure which vehicle you mean, we will ask
- ✓Fuel: live prices, plus a journey fuel cost such as London to Edinburgh
- ✓Fuel price alerts by email: send FUEL ALERT with your town or postcode, fuel and email address
- ✓How many are left: send HOW MANY and a model no longer sold new, for example HOW MANY Saab 9-3
- ✓Recalls: send RECALLS and a make or model, for example RECALLS Ford Puma
- ✓MOT pass rates: send MOT RATE and a model, for example MOT RATE Ford Fiesta
- ✓Diesel driver? Send FUEL CARD for the Accelerate diesel fuel card, up to 5p a litre
- ✓Reply STOP at any time to opt out
Looking for a BMW 5 Series?
See used BMW 5 Series cars listed on the MotifyMe® marketplace.
See 5 Series cars for sale